STM32F103C6T7A STMicroelectronics, STM32F103C6T7A Datasheet - Page 18

• Manufacturer Part Number: STM32F103C6T7A
• Description: MCU ARM 32BIT 32KB FLASH 48LQFP
• Manufacturer: STMicroelectronics
• Series: STM32r

Specifications of STM32F103C6T7A

• Core Processor: ARM® Cortex-M3™
• Core Size: 32-Bit
• Speed: 72MHz
• Connectivity: CAN, I²C, IrDA, LIN, SPI, UART/USART, USB
• Peripherals: DMA, Motor Control PWM, PDR, POR, PVD, PWM, Temp Sensor, WDT
• Number Of I /o: 37
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: FLASH
• Ram Size: 10K x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 3.6 V
• Data Converters: A/D 10x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 105°C
• Package / Case: 48-LQFP
• Featured Product: STM32 Cortex-M3 Companion Products
• Eeprom Size: -
• Cpu Family: STM32
• Device Core: ARM Cortex-M3
• Device Core Size: 32b
• Frequency (max): 72MHz
• Interface Type: CAN/I2C/SPI/USART
• Total Internal Ram Size: 10KB
• # I/os (max): 37
• Number Of Timers - General Purpose: 3
• Operating Supply Voltage (typ): 2.5/3.3V
• Operating Supply Voltage (max): 3.6V
• Operating Supply Voltage (min): 2V
• On-chip Adc: 2(10-chx12-bit)
• Instruction Set Architecture: RISC
• Operating Temp Range: -40C to 105C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 48
• Package Type: LQFP
• For Use With: 497-10048 - BOARD EVAL ACCELEROMETER497-10030 - STARTER KIT FOR STM32KSDKSTM32-PL - KIT IAR KICKSTART STM32 CORTEXM3497-8512 - KIT STARTER FOR STM32F10XE MCU497-8511 - KIT STARTER FOR STM32 512K FLASH497-8505 - KIT STARTER FOR STM32F10XE MCU497-6438 - BOARD EVALUTION FOR STM32 512K497-6289 - KIT PERFORMANCE STICK FOR STM32MCBSTM32UME - BOARD EVAL MCBSTM32 + ULINK-MEMCBSTM32U - BOARD EVAL MCBSTM32 + ULINK2MCBSTM32 - BOARD EVAL FOR STM STM32X SER497-6053 - KIT STARTER FOR STM32497-6052 - KIT STARTER FOR STM32497-6050 - KIT STARTER FOR STM32497-6049 - KIT EVALUATION LOW COST STM32497-6048 - BOARD EVALUATION FOR STM32497-6047 - KIT DEVELOPMENT FOR STM32
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

Description
18/87
Advanced-control timer (TIM1)
The advanced-control timer (TIM1) can be seen as a three-phase PWM multiplexed on 6
channels. It has complementary PWM outputs with programmable inserted dead-times. It
can also be seen as a complete general-purpose timer. The 4 independent channels can be
used for
●
●
●
●
If configured as a general-purpose 16-bit timer, it has the same features as the TIMx timer. If
configured as the 16-bit PWM generator, it has full modulation capability (0-100%).
In debug mode, the advanced-control timer counter can be frozen and the PWM outputs
disabled to turn off any power switch driven by these outputs.
Many features are shared with those of the general-purpose TIM timers which have the
same architecture. The advanced-control timer can therefore work together with the TIM
timers via the Timer Link feature for synchronization or event chaining.
General-purpose timers (TIMx)
There are up to two synchronizable general-purpose timers embedded in the STM32F103xx
performance line devices. These timers are based on a 16-bit auto-reload up/down counter,
a 16-bit prescaler and feature 4 independent channels each for input capture/output
compare, PWM or one-pulse mode output. This gives up to 12 input captures/output
compares/PWMs on the largest packages.
The general-purpose timers can work together with the advanced-control timer via the Timer
Link feature for synchronization or event chaining. Their counter can be frozen in debug
mode. Any of the general-purpose timers can be used to generate PWM outputs. They all
have independent DMA request generation.
These timers are capable of handling quadrature (incremental) encoder signals and the
digital outputs from 1 to 3 hall-effect sensors.
Independent watchdog
The independent watchdog is based on a 12-bit downcounter and 8-bit prescaler. It is
clocked from an independent 40 kHz internal RC and as it operates independently of the
main clock, it can operate in Stop and Standby modes. It can be used either as a watchdog
to reset the device when a problem occurs, or as a free-running timer for application timeout
management. It is hardware- or software-configurable through the option bytes. The counter
can be frozen in debug mode.
Window watchdog
The window watchdog is based on a 7-bit downcounter that can be set as free-running. It
can be used as a watchdog to reset the device when a problem occurs. It is clocked from the
main clock. It has an early warning interrupt capability and the counter can be frozen in
debug mode.
Input capture
Output compare
PWM generation (edge- or center-aligned modes)
One-pulse mode output
Doc ID 15060 Rev 5
STM32F103x4, STM32F103x6