STM32F103C6T7A STMicroelectronics, STM32F103C6T7A Datasheet - Page 47

MCU ARM 32BIT 32KB FLASH 48LQFP

STM32F103C6T7A

Manufacturer Part Number
STM32F103C6T7A
Description
MCU ARM 32BIT 32KB FLASH 48LQFP
Manufacturer
STMicroelectronics
Series
STM32r
Datasheets

Specifications of STM32F103C6T7A

Core Processor
ARM® Cortex-M3™
Core Size
32-Bit
Speed
72MHz
Connectivity
CAN, I²C, IrDA, LIN, SPI, UART/USART, USB
Peripherals
DMA, Motor Control PWM, PDR, POR, PVD, PWM, Temp Sensor, WDT
Number Of I /o
37
Program Memory Size
32KB (32K x 8)
Program Memory Type
FLASH
Ram Size
10K x 8
Voltage - Supply (vcc/vdd)
2 V ~ 3.6 V
Data Converters
A/D 10x12b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 105°C
Package / Case
48-LQFP
Featured Product
STM32 Cortex-M3 Companion Products
Eeprom Size
-
Cpu Family
STM32
Device Core
ARM Cortex-M3
Device Core Size
32b
Frequency (max)
72MHz
Interface Type
CAN/I2C/SPI/USART
Total Internal Ram Size
10KB
# I/os (max)
37
Number Of Timers - General Purpose
3
Operating Supply Voltage (typ)
2.5/3.3V
Operating Supply Voltage (max)
3.6V
Operating Supply Voltage (min)
2V
On-chip Adc
2(10-chx12-bit)
Instruction Set Architecture
RISC
Operating Temp Range
-40C to 105C
Operating Temperature Classification
Industrial
Mounting
Surface Mount
Pin Count
48
Package Type
LQFP
For Use With
497-10048 - BOARD EVAL ACCELEROMETER497-10030 - STARTER KIT FOR STM32KSDKSTM32-PL - KIT IAR KICKSTART STM32 CORTEXM3497-8512 - KIT STARTER FOR STM32F10XE MCU497-8511 - KIT STARTER FOR STM32 512K FLASH497-8505 - KIT STARTER FOR STM32F10XE MCU497-6438 - BOARD EVALUTION FOR STM32 512K497-6289 - KIT PERFORMANCE STICK FOR STM32MCBSTM32UME - BOARD EVAL MCBSTM32 + ULINK-MEMCBSTM32U - BOARD EVAL MCBSTM32 + ULINK2MCBSTM32 - BOARD EVAL FOR STM STM32X SER497-6053 - KIT STARTER FOR STM32497-6052 - KIT STARTER FOR STM32497-6050 - KIT STARTER FOR STM32497-6049 - KIT EVALUATION LOW COST STM32497-6048 - BOARD EVALUATION FOR STM32497-6047 - KIT DEVELOPMENT FOR STM32
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
STM32F103C6T7A
Manufacturer:
ST
Quantity:
1 500
Part Number:
STM32F103C6T7A
Manufacturer:
STMicroelectronics
Quantity:
10 000
Part Number:
STM32F103C6T7A
Manufacturer:
ST
Quantity:
20 000
Part Number:
STM32F103C6T7A
0
Part Number:
STM32F103C6T7ATR
Manufacturer:
STMicroelectronics
Quantity:
10 000
STM32F103x4, STM32F103x6
Table 22.
1. Resonator characteristics given by the crystal/ceramic resonator manufacturer.
2. Based on characterization, not tested in production.
3. The relatively low value of the RF resistor offers a good protection against issues resulting from use in a
4. t
For C
5 pF to 25 pF range (typ.), designed for high-frequency applications, and selected to match
the requirements of the crystal or resonator (see
same size. The crystal manufacturer typically specifies a load capacitance which is the
series combination of C
can be used as a rough estimate of the combined pin and board capacitance) when sizing
C
microcontrollers” available from the ST website www.st.com.
Figure 21. Typical application with an 8 MHz crystal
1. R
Low-speed external clock generated from a crystal/ceramic resonator
The low-speed external (LSE) clock can be supplied with a 32.768 kHz crystal/ceramic
resonator oscillator. All the information given in this paragraph are based on characterization
results obtained with typical external components specified in
the resonator and the load capacitors have to be placed as close as possible to the oscillator
pins in order to minimize output distortion and startup stabilization time. Refer to the crystal
resonator manufacturer for more details on the resonator characteristics (frequency,
package, accuracy).
t
SU(HSE
Symbol
L1
f
OSC_IN
humid environment, due to the induced leakage and the bias condition change. However, it is
recommended to take this point into account if the MCU is used in tough humidity conditions.
oscillation is reached. This value is measured for a standard crystal resonator and it can vary significantly
with the crystal manufacturer
SU(HSE)
R
g
and C
C
EXT
i
2
m
F
L1
(4)
value depends on the crystal characteristics.
and C
Resonator with
integrated capacitors
is the startup time measured from the moment it is enabled (by software) to a stabilized 8 MHz
L2
Oscillator frequency
Feedback resistor
Recommended load capacitance
versus equivalent serial
resistance of the crystal (R
HSE driving current
Oscillator transconductance
startup time
. Refer to the application note AN2867 “Oscillator design guide for ST
HSE 4-16 MHz oscillator characteristics
L2
, it is recommended to use high-quality external ceramic capacitors in the
C L2
C L1
Parameter
L1
and C
8 MH z
resonator
R EXT (1)
Doc ID 15060 Rev 5
L2
. PCB and MCU pin capacitance must be included (10 pF
S
)
(3)
OSC_OU T
OSC_IN
V
DD
V
with 30 pF load
R F
= 3.3 V, V
DD
Conditions
R
Figure
Startup
S
is stabilized
controlled
= 30 Ω
Bias
gain
(1) (2)
IN
21). C
= V
SS
Table
L1
STM32F103xx
Electrical characteristics
and C
Min
25
4
23. In the application,
f HSE
L2
Typ
200
30
2
are usually the
8
Max
ai14145
16
1
mA/V
MHz
Unit
mA
ms
47/87
pF

Related parts for STM32F103C6T7A