STM32F101R4T6A STMicroelectronics, STM32F101R4T6A Datasheet - Page 31

• Manufacturer Part Number: STM32F101R4T6A
• Description: MCU ARM 32BIT 16K FLASH 64-LQFP
• Manufacturer: STMicroelectronics
• Series: STM32r

Specifications of STM32F101R4T6A

• Core Processor: ARM® Cortex-M3™
• Core Size: 32-Bit
• Speed: 36MHz
• Connectivity: I²C, IrDA, LIN, SPI, UART/USART
• Peripherals: DMA, PDR, POR, PVD, PWM, Temp Sensor, WDT
• Number Of I /o: 51
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Ram Size: 4K x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 3.6 V
• Data Converters: A/D 16x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-LQFP
• Processor Series: STM32F101x
• Core: ARM Cortex M3
• Data Bus Width: 32 bit
• Data Ram Size: 4 KB
• Interface Type: I2C, SPI, USART
• Maximum Clock Frequency: 36 MHz
• Number Of Programmable I/os: 51
• Number Of Timers: 2
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 12 bit, 16 Channel
• For Use With: 497-10030 - STARTER KIT FOR STM32497-8853 - BOARD DEMO STM32 UNIV USB-UUSCIKSDKSTM32-PL - KIT IAR KICKSTART STM32 CORTEXM3497-8512 - KIT STARTER FOR STM32F10XE MCU497-8505 - KIT STARTER FOR STM32F10XE MCU497-8304 - KIT STM32 MOTOR DRIVER BLDC497-6438 - BOARD EVALUTION FOR STM32 512K497-6289 - KIT PERFORMANCE STICK FOR STM32MCBSTM32UME - BOARD EVAL MCBSTM32 + ULINK-MEMCBSTM32U - BOARD EVAL MCBSTM32 + ULINK2497-6053 - KIT STARTER FOR STM32497-6052 - KIT STARTER FOR STM32497-6050 - KIT STARTER FOR STM32497-6049 - KIT EVALUATION LOW COST STM32497-6048 - BOARD EVALUATION FOR STM32497-6047 - KIT DEVELOPMENT FOR STM32497-5046 - KIT TOOL FOR ST7/UPSD/STR7 MCU
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details
• Other names: 497-8314

STM32F101x4, STM32F101x6
5.3.2
5.3.3
Table 8.
1. When the ADC is used, refer to
2. It is recommended to power V
3. If T
4. In low power dissipation state, T
Operating conditions at power-up / power-down
Subject to general operating conditions for T
Table 9.
Embedded reset and power control block characteristics
The parameters given in
temperature and V
Symbol
Symbol
between V
characteristics on page
Table 6.2: Thermal characteristics on page
t
VDD
P
T
T
A
A
D
J
is lower, higher P
V
V
DD
General operating conditions (continued)
Operating conditions at power-up / power-down
DD
DD
Power dissipation at T
85 °C
Ambient temperature
Junction temperature range
and V
rise time rate
fall time rate
Parameter
(3)
DD
DDA
D
Parameter
supply voltage conditions summarized in
74).
can be tolerated during power-up and operation.
values are allowed as long as T
Table 10
DD
A
Table 42: ADC
and V
can be extended to this range as long as T
Doc ID 15058 Rev 5
A
are derived from tests performed under the ambient
=
DDA
74).
from the same source. A maximum difference of 300 mV
characteristics.
LQFP64
LQFP48
VFQFPN36
Maximum power dissipation
Low power dissipation
A
Conditions
.
J
does not exceed T
Conditions
(4)
Table
J
J
max (see
Electrical characteristics
does not exceed T
Min
8.
Min
–40
20
–40
–40
0
Table 6.2: Thermal
1000
Max
444
363
105
105
85
Max
∞
∞
J
max (see
Unit
mW
°C
°C
°C
Unit
µs/V
31/79