ST62T65CM6 STMicroelectronics, ST62T65CM6 Datasheet - Page 42

• Manufacturer Part Number: ST62T65CM6
• Description: IC MCU 8BIT OTP/EPROM 28 PSOIC
• Manufacturer: STMicroelectronics
• Series: ST6r

Specifications of ST62T65CM6

• Core Processor: ST6
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: SPI
• Peripherals: LED, LVD, POR, WDT
• Number Of I /o: 21
• Program Memory Size: 3.8KB (3.8K x 8)
• Program Memory Type: OTP
• Eeprom Size: 128 x 8
• Ram Size: 128 x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 6 V
• Data Converters: A/D 13x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-SOIC (7.5mm Width)
• Controller Family/series: ST6
• No. Of I/o's: 21
• Eeprom Memory Size: 128Byte
• Ram Memory Size: 128Byte
• Cpu Speed: 8MHz
• No. Of Timers: 2
• Rohs Compliant: Yes
• Processor Series: ST62T6x
• Core: ST6
• Data Bus Width: 8 bit
• Data Ram Size: 128 B
• Interface Type: SCI
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 21
• Number Of Timers: 1
• Operating Supply Voltage: 3 V to 6 V
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: ST62GP-EMU2, ST62E2XC-EPB/110, ST62E6XC-EPB/US, STREALIZER-II
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8 bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 497-2103-5

ST6255C ST6265C ST6265B
4.2 TIMER
The MCU features an on-chip Timer peripheral,
consisting of an 8-bit counter with a 7-bit program-
mable prescaler, giving a maximum count of 2
The peripheral may be configured in three different
operating modes.
Figure 25
external TIMER pin is available to the user. The
content of the 8-bit counter can be read/written in
the Timer/Counter register, TCR, while the state of
the 7-bit prescaler can be read in the PSC register.
The control logic device is managed in the TSCR
register as described in the following paragraphs.
The 8-bit counter is decremented by the output
(rising edge) coming from the 7-bit prescaler and
can be loaded and read under program control.
When it decrements to zero then the TMZ (Timer
Zero) bit in the TSCR is set to “1”. If the ETI (Ena-
ble Timer Interrupt) bit in the TSCR is also set to
“1”, an interrupt request is generated as described
in the Interrupt Chapter. The Timer interrupt can
be used to exit the MCU from WAIT mode.
Figure 25. Timer Block Diagram
42/84
TIMER
shows the Timer Block Diagram. The
PSC
f
OSC
8
6
5
4
3
2
1
0
:12
SYNCHRONIZATION
LOGIC
SELECT
1 OF 7
15
.
The prescaler input can be the internal frequency
f
the TIMER pin. The prescaler decrements on the
rising edge. Depending on the division factor pro-
grammed by PS2, PS1 and PS0 bits in the TSCR.
The clock input of the timer/counter register is mul-
tiplexed to different sources. For division factor 1,
the clock input of the prescaler is also that of timer/
counter; for factor 2, bit 0 of the prescaler register
is connected to the clock input of TCR. This bit
changes its state at half the frequency of the pres-
caler input clock. For factor 4, bit 1 of the PSC is
connected to the clock input of TCR, and so forth.
The prescaler initialize bit, PSI, in the TSCR regis-
ter must be set to “1” to allow the prescaler (and
hence the counter) to start. If it is cleared to “0”, all
the prescaler bits are set to “1” and the counter is
inhibited from counting. The prescaler can be
loaded with any value between 0 and 7Fh, if bit
PSI is set to “1”. The prescaler tap is selected by
means of the PS2/PS1/PS0 bits in the control reg-
ister.
Figure 26
INT
DATABUS 8
COUNTER
8-BIT
divided by 12 or an external clock applied to
8
3
illustrates the Timer’s working principle.
TMZ ETI
b7
LATCH
b6
STATUS/CONTROL
TOUT
b5
REGISTER
DOUT
b4
8
b3
PSI
b2
PS2
b1
PS1
VA00009
b0
PS0
INTERRUPT
LINE