IC MCU 8BIT OTP/EPROM 28 PSOIC

ST62T65CM6

Manufacturer Part NumberST62T65CM6
DescriptionIC MCU 8BIT OTP/EPROM 28 PSOIC
ManufacturerSTMicroelectronics
SeriesST6
ST62T65CM6 datasheet
 


Specifications of ST62T65CM6

Core ProcessorST6Core Size8-Bit
Speed8MHzConnectivitySPI
PeripheralsLED, LVD, POR, WDTNumber Of I /o21
Program Memory Size3.8KB (3.8K x 8)Program Memory TypeOTP
Eeprom Size128 x 8Ram Size128 x 8
Voltage - Supply (vcc/vdd)3 V ~ 6 VData ConvertersA/D 13x8b
Oscillator TypeInternalOperating Temperature-40°C ~ 85°C
Package / Case28-SOIC (7.5mm Width)Controller Family/seriesST6
No. Of I/o's21Eeprom Memory Size128Byte
Ram Memory Size128ByteCpu Speed8MHz
No. Of Timers2Rohs CompliantYes
Processor SeriesST62T6xCoreST6
Data Bus Width8 bitData Ram Size128 B
Interface TypeSCIMaximum Clock Frequency8 MHz
Number Of Programmable I/os21Number Of Timers1
Operating Supply Voltage3 V to 6 VMaximum Operating Temperature+ 125 C
Mounting StyleSMD/SMTDevelopment Tools By SupplierST62GP-EMU2, ST62E2XC-EPB/110, ST62E6XC-EPB/US, STREALIZER-II
Minimum Operating Temperature- 40 COn-chip Adc8 bit
Lead Free Status / RoHS StatusLead free / RoHS CompliantOther names497-2103-5
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
Page 21
22
Page 22
23
Page 23
24
Page 24
25
Page 25
26
Page 26
27
Page 27
28
Page 28
29
Page 29
30
Page 30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
Page 28/84

Download datasheet (2Mb)Embed
PrevNext
ST6255C ST6265C ST6265B
DIGITAL WATCHDOG (Cont’d)
3.2.1 Digital Watchdog Register (DWDR)
Address: 0D8h — Read/Write
Reset status: 1111 1110b
7
T0
T1
T2
T3
T4
Bit 0 = C: Watchdog Control bit
If the hardware option is selected, this bit is forced
high and the user cannot change it (the Watchdog
is always active). When the software option is se-
lected, the Watchdog function is activated by set-
ting bit C to 1, and cannot then be disabled (save
by resetting the MCU).
When C is kept low the counter can be used as a
7-bit timer.
This bit is cleared to “0” on Reset.
Bit 1 = SR: Software Reset bit
This bit triggers a Reset when cleared.
When C = “0” (Watchdog disabled) it is the MSB of
the 7-bit timer.
This bit is set to “1” on Reset.
Bits 2-7 = T5-T0: Downcounter bits
It should be noted that the register bits are re-
versed and shifted with respect to the physical
counter: bit-7 (T0) is the LSB of the Watchdog
downcounter and bit-2 (T5) is the MSB.
These bits are set to “1” on Reset.
3.2.2 Application Notes
The Watchdog plays an important supporting role
in the high noise immunity of ST62xx devices, and
28/84
should be used wherever possible. Watchdog re-
lated options should be selected on the basis of a
trade-off between application security and STOP
mode availability.
When STOP mode is not required, hardware acti-
3.2.1.1
0
vation without EXTERNAL STOP MODE CON-
TROL should be preferred, as it provides maxi-
T5
SR
C
mum security, especially during power-on.
When STOP mode is required, hardware activa-
tion and EXTERNAL STOP MODE CONTROL
should be chosen. NMI should be high by default,
to allow STOP mode to be entered when the MCU
is idle.
The NMI pin can be connected to an I/O line (see
Figure
18) to allow its state to be controlled by soft-
ware. The I/O line can then be used to keep NMI
low while Watchdog protection is required, or to
avoid noise or key bounce. When no more
processing is required, the I/O line is released and
the device placed in STOP mode for lowest power
consumption.
When software activation is selected and the
Watchdog is not activated, the downcounter may
be used as a simple 7-bit timer (remember that the
bits are in reverse order).
The software activation option should be chosen
only when the Watchdog counter is to be used as
a timer. To ensure the Watchdog has not been un-
expectedly activated, the following instructions
should be executed within the first 27 instructions:
jrr 0, WD, #+3
ldi WD, 0FDH