ST62T60CM6 STMicroelectronics, ST62T60CM6 Datasheet - Page 37

• Manufacturer Part Number: ST62T60CM6
• Description: IC MCU 8BIT OTP/EPROM 20 PSOIC
• Manufacturer: STMicroelectronics
• Series: ST6r

Specifications of ST62T60CM6

• Core Processor: ST6
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: SPI
• Peripherals: LED, LVD, POR, WDT
• Number Of I /o: 13
• Program Memory Size: 3.8KB (3.8K x 8)
• Program Memory Type: OTP
• Eeprom Size: 128 x 8
• Ram Size: 128 x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 6 V
• Data Converters: A/D 7x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 20-SOIC (7.5mm Width)
• Processor Series: ST62T6x
• Core: ST6
• Data Bus Width: 8 bit
• Data Ram Size: 128 B
• Interface Type: SPI
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 13
• Number Of Timers: 2
• Operating Supply Voltage: 3 V to 6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: ST622XC-KIT/110, ST62GP-EMU2, ST62E2XC-EPB/110, ST62E6XC-EPB/US, STREALIZER-II
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8 bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 497-2102-5

ST6253C ST6263C ST6263B ST6260C ST6260B
I/O PORTS (Cont’d)
4.1.1 Operating Modes
Each pin may be individually programmed as input
or output with various configurations.
This is achieved by writing the relevant bit in the
Data (DR), Data Direction (DDR) and Option reg-
isters (OR).
configurations which can be selected by user soft-
ware.
4.1.1.1 Input Options
Pull-up, High Impedance Option. All input lines
can be individually programmed with or without an
internal pull-up by programming the OR and DR
registers accordingly. If the pull-up option is not
selected, the input pin will be in the high-imped-
ance state.
Table 10. I/O Port Option Selection
Note: X = Don’t care
37/83
DDR
0
0
0
0
1
1
Table 10
OR
0
0
1
1
0
1
illustrates the various port
DR
X
X
0
1
0
1
Output
Output
Mode
Input
Input
Input
Input
With pull-up, no interrupt
No pull-up, no interrupt
With pull-up and with interrupt
Analog input (when available)
Open-drain output (20mA sink when available)
Push-pull output (20mA sink when available)
4.1.1.2 Interrupt Options
All input lines can be individually connected by
software to the interrupt system by programming
the OR and DR registers accordingly. The inter-
rupt trigger modes (falling edge, rising edge and
low level) can be configured by software as de-
scribed in the Interrupt Chapter for each port.
4.1.1.3 Analog Input Options
Some pins can be configured as analog inputs by
programming the OR and DR registers according-
ly. These analog inputs are connected to the on-
chip 8-bit Analog to Digital Converter. ONLY ONE
pin should be programmed as an analog input at
any time, since by selecting more than one input
simultaneously their pins will be effectively short-
ed.
Option