R5F21324CNSP#U0 Renesas Electronics America, R5F21324CNSP#U0 Datasheet - Page 416

• Manufacturer Part Number: R5F21324CNSP#U0
• Description: MCU 1KB FLASH 16K ROM 20-LSSOP
• Manufacturer: Renesas Electronics America
• Series: R8C/3x/32Cr

Specifications of R5F21324CNSP#U0

• Core Processor: R8C
• Core Size: 16/32-Bit
• Speed: 20MHz
• Connectivity: I²C, LIN, SIO, SSU, UART/USART
• Peripherals: POR, PWM, Voltage Detect, WDT
• Number Of I /o: 15
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Ram Size: 1.5K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 4x10b
• Oscillator Type: Internal
• Operating Temperature: -20°C ~ 85°C
• Package / Case: 20-LSSOP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

R8C/32C Group
REJ09B0573-0100 Rev.1.00 Dec. 18, 2009
Page 387 of 573
24.5.3
Figure 24.12 shows an Example of Synchronous Serial Communication Unit Operation during Data Reception
(4-Wire Bus Communication Mode, 8-Bit SSU Data Transfer Length). During data reception, synchronous
serial communication unit operates as described below (The data transfer length can be set from 8 to 16 bits
using the SSBR register).
When the MCU is set as the master device, it outputs a synchronous clock and inputs data. When the MCU is
set as a slave device, it outputs data synchronized with the input clock while the SCS pin receives “L” input.
When the MCU is set as the master device, it outputs a receive clock and starts receiving by performing a
dummy read of the SSRDR register.
After 8 bits of data are received, the RDRF bit in the SSSR register is set to 1 (data in the SSRDR register) and
receive data is stored in the SSRDR register. When the RIE bit in the SSER register is set to 1 (RXI and OEI
interrupt requests enabled), an RXI interrupt request is generated. When the SSRDR register is read, the RDRF
bit is automatically set to 0 (no data in the SSRDR register).
Read the receive data after setting the RSSTP bit in the SSCRH register to 1 (after receiving 1-byte data, the
receive operation is completed). Synchronous serial communication unit outputs a clock for receiving 8 bits of
data and stops. After that, set the RE bit in the SSER register to 0 (receive disabled) and the RSSTP bit to 0
(receive operation is continued after receiving 1-byte data) and read the receive data. When the SSRDR register
is read while the RE bit is set to 1 (receive enabled), a receive clock is output again.
When the 8th clock rises while the RDRF bit is set to 1, the ORER bit in the SSSR register is set to 1 (overrun
error: OEI) and the operation is stopped. When the ORER bit is set to 1, reception cannot be performed.
Confirm that the ORER bit is set to 0 before restarting reception.
The timing with which bits RDRF and ORER are set to 1 varies depending on the setting of the CPHS bit in the
SSMR register. Figure 24.12 shows when bits RDRF and ORER are set to 1.
When the CPHS bit is set to 1 (data download at the odd edges), bits RDRF and ORER are set to 1 at some
point during the frame.
The sample flowchart is the same as that for the clock synchronous communication mode (refer to Figure 24.8
Sample Flowchart of Data Reception (MSS = 1) (Clock Synchronous Communication Mode)).
Data Reception
24. Synchronous Serial Communication Unit (SSU)