MC908LJ24CPBER Freescale Semiconductor, MC908LJ24CPBER Datasheet - Page 311

• Manufacturer Part Number: MC908LJ24CPBER
• Description: IC MCU 24K FLASH 4/8MHZ 64-LQFP
• Manufacturer: Freescale Semiconductor
• Series: HC08r

Specifications of MC908LJ24CPBER

• Core Processor: HC08
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: I²C, IRSCI, SPI
• Peripherals: LCD, LVD, POR, PWM
• Number Of I /o: 40
• Program Memory Size: 24KB (24K x 8)
• Program Memory Type: FLASH
• Ram Size: 768 x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 5.5 V
• Data Converters: A/D 6x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-LQFP
• Controller Family/series: HC08
• No. Of I/o's: 40
• Ram Memory Size: 768Byte
• Cpu Speed: 8MHz
• No. Of Timers: 2
• Embedded Interface Type: I2C, SCI, SPI
• Rohs Compliant: Yes
• Processor Series: HC08LJ
• Core: HC08
• Data Bus Width: 8 bit
• Data Ram Size: 768 B
• Interface Type: SCI, SPI
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 48
• Number Of Timers: 4
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: FSICEBASE, M68EML08LJLKE, ZK-HC08LX-A, M68CBL05CE
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 6 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

14.13.5 CGND (Clock Ground)
MC68HC908LJ24/LK24 — Rev. 2.1
Freescale Semiconductor
When an SPI is configured as a master, the SS input can be used in
conjunction with the MODF flag to prevent multiple masters from driving
MOSI and SPSCK. (See
SS pin to set the MODF flag, the MODFEN bit in the SPSCK register
must be set. If the MODFEN bit is low for an SPI master, the SS pin can
be used as a general-purpose I/O under the control of the data direction
register of the shared I/O port. With MODFEN high, it is an input-only pin
to the SPI regardless of the state of the data direction register of the
shared I/O port.
The CPU can always read the state of the SS pin by configuring the
appropriate pin as an input and reading the port data register. (See
Table
CGND is the ground return for the serial clock pin, SPSCK, and the
ground for the port output buffers. It is internally connected to V
shown in
Note 1. X = Don’t care
SPE
0
1
1
1
14-3.)
Serial Peripheral Interface Module (SPI)
SPMSTR
Table
X
0
1
1
(1)
14-1.
MODFEN
Table 14-3. SPI Configuration
X
X
0
1
14.8.2 Mode Fault
Master without MODF
SPI Configuration
Master with MODF
Not enabled
Slave
Serial Peripheral Interface Module (SPI)
Error.) For the state of the
General-purpose I/O;
General-purpose I/O;
State of SS Logic
SS ignored by SPI
SS ignored by SPI
Input-only to SPI
Input-only to SPI
Data Sheet
I/O Signals
SS
as
311