MC908LJ24CFUER Freescale Semiconductor, MC908LJ24CFUER Datasheet - Page 255

• Manufacturer Part Number: MC908LJ24CFUER
• Description: IC MCU 24K FLASH 8MHZ SPI 64-QFP
• Manufacturer: Freescale Semiconductor
• Series: HC08r

Specifications of MC908LJ24CFUER

• Core Processor: HC08
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: I²C, IRSCI, SPI
• Peripherals: LCD, LVD, POR, PWM
• Number Of I /o: 40
• Program Memory Size: 24KB (24K x 8)
• Program Memory Type: FLASH
• Ram Size: 768 x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 5.5 V
• Data Converters: A/D 6x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-QFP
• Processor Series: HC08LJ
• Core: HC08
• Data Bus Width: 8 bit
• Data Ram Size: 768 B
• Interface Type: SCI, SPI
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 48
• Number Of Timers: 4
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: FSICEBASE, M68EML08LJLKE, ZK-HC08LX-A, M68CBL05CE
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 6 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

13.7.2.1 Character Length
13.7.2.2 Character Transmission
MC68HC908LJ24/LK24 — Rev. 2.1
Freescale Semiconductor
Infrared Serial Communications Interface Module (IRSCI)
The transmitter can accommodate either 8-bit or 9-bit data. The state of
the M bit in SCI control register 1 (SCC1) determines character length.
When transmitting 9-bit data, bit T8 in SCI control register 3 (SCC3) is
the ninth bit (bit 8).
During an SCI transmission, the transmit shift register shifts a character
out to the TxD pin. The SCI data register (SCDR) is the write-only buffer
between the internal data bus and the transmit shift register. To initiate
an SCI transmission:
At the start of a transmission, transmitter control logic automatically
loads the transmit shift register with a preamble of logic 1s. After the
preamble shifts out, control logic transfers the SCDR data into the
transmit shift register. A logic 0 start bit automatically goes into the least
significant bit position of the transmit shift register. A logic 1 stop bit goes
into the most significant bit position.
The SCI transmitter empty bit, SCTE, in SCS1 becomes set when the
SCDR transfers a byte to the transmit shift register. The SCTE bit
indicates that the SCDR can accept new data from the internal data bus.
If the SCI transmit interrupt enable bit, SCTIE, in SCC2 is also set, the
SCTE bit generates a transmitter interrupt request.
When the transmit shift register is not transmitting a character, the TxD
pin goes to the idle condition, logic 1. If at any time software clears the
ENSCI bit in SCI control register 1 (SCC1), the transmitter and receiver
relinquish control of the port pins.
1. Enable the SCI by writing a logic 1 to the enable SCI bit (ENSCI)
2. Enable the transmitter by writing a logic 1 to the transmitter enable
3. Clear the SCI transmitter empty bit by first reading SCI status
4. Repeat step 3 for each subsequent transmission.
in SCI control register 1 (SCC1).
bit (TE) in SCI control register 2 (SCC2).
register 1 (SCS1) and then writing to the SCDR.
Infrared Serial Communications Interface Module (IRSCI)
SCI Functional Description
Data Sheet
255