MC908LJ24CFUER Freescale Semiconductor, MC908LJ24CFUER Datasheet - Page 273

• Manufacturer Part Number: MC908LJ24CFUER
• Description: IC MCU 24K FLASH 8MHZ SPI 64-QFP
• Manufacturer: Freescale Semiconductor
• Series: HC08r

Specifications of MC908LJ24CFUER

• Core Processor: HC08
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: I²C, IRSCI, SPI
• Peripherals: LCD, LVD, POR, PWM
• Number Of I /o: 40
• Program Memory Size: 24KB (24K x 8)
• Program Memory Type: FLASH
• Ram Size: 768 x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 5.5 V
• Data Converters: A/D 6x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-QFP
• Processor Series: HC08LJ
• Core: HC08
• Data Bus Width: 8 bit
• Data Ram Size: 768 B
• Interface Type: SCI, SPI
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 48
• Number Of Timers: 4
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: FSICEBASE, M68EML08LJLKE, ZK-HC08LX-A, M68CBL05CE
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 6 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

MC68HC908LJ24/LK24 — Rev. 2.1
Freescale Semiconductor
NOTE:
NOTE:
NOTE:
Infrared Serial Communications Interface Module (IRSCI)
Writing to the TE bit is not allowed when the enable SCI bit (ENSCI) is
clear. ENSCI is in SCI control register 1.
RE — Receiver Enable Bit
Writing to the RE bit is not allowed when the enable SCI bit (ENSCI) is
clear. ENSCI is in SCI control register 1.
RWU — Receiver Wakeup Bit
SBK — Send Break Bit
Do not toggle the SBK bit immediately after setting the SCTE bit.
Toggling SBK before the preamble begins causes the SCI to send a
break character instead of a preamble.
(logic 1). Clearing and then setting TE during a transmission queues
an idle character to be sent after the character currently being
transmitted. Reset clears the TE bit.
Setting this read/write bit enables the receiver. Clearing the RE bit
disables the receiver but does not affect receiver interrupt flag bits.
Reset clears the RE bit.
This read/write bit puts the receiver in a standby state during which
receiver interrupts are disabled. The WAKE bit in SCC1 determines
whether an idle input or an address mark brings the receiver out of the
standby state and clears the RWU bit. Reset clears the RWU bit.
Setting and then clearing this read/write bit transmits a break
character followed by a logic 1. The logic 1 after the break character
guarantees recognition of a valid start bit. If SBK remains set, the
transmitter continuously transmits break characters with no logic 1s
between them. Reset clears the SBK bit.
1 = Transmitter enabled
0 = Transmitter disabled
1 = Receiver enabled
0 = Receiver disabled
1 = Standby state
0 = Normal operation
1 = Transmit break characters
0 = No break characters being transmitted
Infrared Serial Communications Interface Module (IRSCI)
I/O Registers
Data Sheet
273