R5F21334CNFP#U0 Renesas Electronics America, R5F21334CNFP#U0 Datasheet - Page 171

MCU 1KB FLASH 16K ROM 32-LQFP

R5F21334CNFP#U0

Manufacturer Part Number
R5F21334CNFP#U0
Description
MCU 1KB FLASH 16K ROM 32-LQFP
Manufacturer
Renesas Electronics America
Series
R8C/3x/33Cr
Datasheet

Specifications of R5F21334CNFP#U0

Core Processor
R8C
Core Size
16/32-Bit
Speed
20MHz
Connectivity
I²C, LIN, SIO, SSU, UART/USART
Peripherals
POR, PWM, Voltage Detect, WDT
Number Of I /o
27
Program Memory Size
16KB (16K x 8)
Program Memory Type
FLASH
Ram Size
1.5K x 8
Voltage - Supply (vcc/vdd)
1.8 V ~ 5.5 V
Data Converters
A/D 12x10b; D/A 2x8b
Oscillator Type
Internal
Operating Temperature
-20°C ~ 85°C
Package / Case
32-LQFP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
R5F21334CNFP#U0
Manufacturer:
Renesas Electronics America
Quantity:
135
Company:
Part Number:
R5F21334CNFP#U0R5F21334CNFP#V2
Manufacturer:
RENESAS
Quantity:
5 600
Company:
Part Number:
R5F21334CNFP#U0R5F21334CNFP#V2
Manufacturer:
Renesas Electronics America
Quantity:
10 000
Company:
Part Number:
R5F21334CNFP#U0R5F21334CNFP#X6
Manufacturer:
Renesas Electronics America
Quantity:
10 000
R8C/33C Group
REJ09B0570-0100 Rev.1.00 Dec. 14, 2009
Page 141 of 589
Figure 11.3
11.3.4
Address Bus
CPU Clock
Data Bus
The following describes an interrupt sequence which is performed from when an interrupt request is
acknowledged until the interrupt routine is executed.
When an interrupt request is generated while an instruction is being executed, the CPU determines its interrupt
priority level after the instruction is completed. The CPU starts the interrupt sequence from the following cycle.
However, for the SMOVB, SMOVF, SSTR, or RMPA instruction, if an interrupt request is generated while the
instruction is being executed, the MCU suspends the instruction to start the interrupt sequence. The interrupt
sequence is performed as indicated below.
Figure 11.3 shows the Time Required for Executing Interrupt Sequence.
(1) The CPU obtains interrupt information (interrupt number and interrupt request level) by reading address
(2) The FLG register is saved to a temporary register
(3) The I, D and U flags in the FLG register are set as follows:
(4) The CPU internal temporary register
(5) The PC is saved on the stack.
(6) The interrupt priority level of the acknowledged interrupt is set in the IPL.
(7) The starting address of the interrupt routine set in the interrupt vector is stored in the PC.
After the interrupt sequence is completed, instructions are executed from the starting address of the interrupt
routine.
Notes:
Note:
WR
RD
The indeterminate state depends on the instruction queue buffer.
A read cycle occurs when the instruction queue buffer is ready to acknowledge instructions.
00000h. The IR bit for the corresponding interrupt is set to 0 (no interrupt requested).
sequence.
The I flag is set to 0 (interrupts disabled).
The D flag is set to 0 (single-step interrupt disabled).
The U flag is set to 0 (ISP selected).
However, the U flag does not change state if an INT instruction for software interrupt number 32 to 63 is
executed.
1. These registers cannot be accessed by the user.
2. Refer to 11.7 Timer RC Interrupt, Synchronous Serial Communication Unit Interrupt, I
Interrupt Sequence
Interface Interrupt, and Flash Memory Interrupt (Interrupts with Multiple Interrupt Request
Sources) for the IR bit operations of the timer RC Interrupt, the Synchronous Serial Communication
unit Interrupt, and the I
1
Time Required for Executing Interrupt Sequence
2
Address
0000h
information
Interrupt
3
4
5
Undefined
2
Undefined
C bus Interface Interrupt.
Undefined
6
7
(1)
is saved on the stack.
8
SP-2 SP-1
9
contents
SP-2
10
(1)
contents
SP-1
in the CPU immediately before entering the interrupt
SP-4
11
contents
SP-4
12
SP-3
contents
SP-3
13
VEC
14
contents
VEC
15
VEC+1
contents
VEC+1
16
17
(2)
VEC+2
contents
VEC+2
18
11. Interrupts
19
2
PC
C bus
20

Related parts for R5F21334CNFP#U0