R5F21334CNFP#U0 Renesas Electronics America, R5F21334CNFP#U0 Datasheet - Page 381

• Manufacturer Part Number: R5F21334CNFP#U0
• Description: MCU 1KB FLASH 16K ROM 32-LQFP
• Manufacturer: Renesas Electronics America
• Series: R8C/3x/33Cr

Specifications of R5F21334CNFP#U0

• Core Processor: R8C
• Core Size: 16/32-Bit
• Speed: 20MHz
• Connectivity: I²C, LIN, SIO, SSU, UART/USART
• Peripherals: POR, PWM, Voltage Detect, WDT
• Number Of I /o: 27
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Ram Size: 1.5K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 12x10b; D/A 2x8b
• Oscillator Type: Internal
• Operating Temperature: -20°C ~ 85°C
• Package / Case: 32-LQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

R8C/33C Group
REJ09B0570-0100 Rev.1.00 Dec. 14, 2009
Page 351 of 589
Figure 22.12
22.4.6
22.4.7
input signal
Sampling
RXD2
clock
The CTS function is used to start transmit operation when “L” is applied to the CTS2/RTS2 pin. Transmit
operation begins when the CTS2/RTS2 pin is held low. If the “L” signal is switched to “H” during transmit
operation, the operation stops after the ongoing transmit/receive operation is completed.
When the RTS function is used, the CTS2/RTS2 pin outputs “L” when the MCU is ready for a receive
operation. The output level goes high at the first falling edge of the CLK2 pin.
• The CRD bit in the U2C0 register = 1 (CTS/RTS function disabled)
• The CRD bit = 0, CRS bit = 0 (CTS function selected)
• The CRD bit = 0, CRS bit = 1 (RTS function selected)
When the DF2EN bit in the URXDF register is set to 1 (RXD2 digital filer enabled), the RXD2 input signal is
loaded internally via the digital filter circuit for noise reduction. The noise canceller consists of three cascaded
latch circuits and a match detection circuit. The RXD2 input signal is sampled on the internal basic clock with a
frequency 16 times the bit rate. It is recognized as a signal and the level is passed forward to the next circuit
when three latch outputs match. When the outputs do not match, the previous value is retained.
In other words, when the level is changed within three clocks, the change is recognized as not a signal but noise.
Figure 22.12 shows a Block Diagram of RXD2 Digital Filter Circuit.
The CTS2/RTS2 pin operates as the programmable I/O function.
The CTS2/RTS2 pin operates as the CTS function.
The CTS2/RTS2 pin operates as the RTS function.
Note:
CTS/RTS Function
RXD2 Digital Filter Select Function
Internal basic clock
1. When the CKDIR bit in the U2MR register is 0 (internal clock), the internal basic clock is set to fj/(n+1)
Sampling clock
D
(fj = f1, f8, f32, fC; n = setting value in the U2BRG register).
When the CKDIR bit in the U2MR register is 1 (external clock), the internal basic clock is set to fEXT/(n+1)
(fEXT is input from the CLK2 pin. n = setting value in the U2BRG register).
Block Diagram of RXD2 Digital Filter Circuit
period
Latch
C
(1)
Q
D
Latch
C
Q
D
Latch
C
Q
detection
Match
circuit
(DF2EN bit)
22. Serial Interface (UART2)
URXDF
register
Internal RXD2
input signal