R5F21334CNFP#U0 Renesas Electronics America, R5F21334CNFP#U0 Datasheet - Page 451

MCU 1KB FLASH 16K ROM 32-LQFP

R5F21334CNFP#U0

Manufacturer Part Number
R5F21334CNFP#U0
Description
MCU 1KB FLASH 16K ROM 32-LQFP
Manufacturer
Renesas Electronics America
Series
R8C/3x/33Cr
Datasheet

Specifications of R5F21334CNFP#U0

Core Processor
R8C
Core Size
16/32-Bit
Speed
20MHz
Connectivity
I²C, LIN, SIO, SSU, UART/USART
Peripherals
POR, PWM, Voltage Detect, WDT
Number Of I /o
27
Program Memory Size
16KB (16K x 8)
Program Memory Type
FLASH
Ram Size
1.5K x 8
Voltage - Supply (vcc/vdd)
1.8 V ~ 5.5 V
Data Converters
A/D 12x10b; D/A 2x8b
Oscillator Type
Internal
Operating Temperature
-20°C ~ 85°C
Package / Case
32-LQFP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
R5F21334CNFP#U0
Manufacturer:
Renesas Electronics America
Quantity:
135
Company:
Part Number:
R5F21334CNFP#U0R5F21334CNFP#V2
Manufacturer:
RENESAS
Quantity:
5 600
Company:
Part Number:
R5F21334CNFP#U0R5F21334CNFP#V2
Manufacturer:
Renesas Electronics America
Quantity:
10 000
Company:
Part Number:
R5F21334CNFP#U0R5F21334CNFP#X6
Manufacturer:
Renesas Electronics America
Quantity:
10 000
R8C/33C Group
REJ09B0570-0100 Rev.1.00 Dec. 14, 2009
Page 421 of 589
25.4.2
In master transmit mode, the master device outputs the transmit clock and data, and the slave device returns an
acknowledge signal.
Figures 25.5 and 25.6 show the Operating Timing in Master Transmit Mode (I
The transmit procedure and operation in master transmit mode are as follows.
(1) Set the STOP bit in the ICSR register to 0 for initialization, and set the ICE bit in the ICCR1 register to 1
(2) After confirming that the bus is released by reading the BBSY bit in the ICCR2 register, set bits TRS and
(3) After confirming that the TDRE bit in the ICSR register is set to 1 (data is transferred from registers ICDRT
(4) When 1 byte of data transmission is completed while the TDRE bit is set to 1, the TEND bit in the ICSR
(5) Write the transmit data after the 2nd byte to the ICDRT register every time the TDRE bit is set to 1.
(6) When the number of bytes to be transmitted is written to the ICDRT register, wait until the TEND bit is set
(7) When the STOP bit in the ICSR register is set to 1, return to slave receive mode.
(transfer operation enabled). Then, set bits WAIT and MLS in the ICMR register and bits CKS0 to CKS3 in
the ICCR1 register (initial setting).
MST in the ICCR1 register to master transmit mode. Then, write 1 to the BBSY bit and 0 to the SCP bit
with the MOV instruction (start condition generated). This will generate a start condition.
to ICDRS), write transmit data to the ICDRT register (data in which a slave address and R/W are indicated
in the 1st byte). At this time, the TDRE bit is automatically set to 0. When data is transferred from registers
ICDRT to ICDRS, the TDRE bit is set to 1 again.
register is set to 1 at the rising edge of the 9th clock cycle of the transmit clock. After confirming that the
slave device is selected by reading the ACKBR bit in the ICIER register, write the 2nd byte of data to the
ICDRT register. Since the slave device is not acknowledged when the ACKBR bit is set to 1, generate a
stop condition. Stop condition generation is enabled by writing 0 to the BBSY bit and 0 to the SCP bit with
the MOV instruction. The SCL signal is fixed “L” until data is ready or a stop condition is generated.
to 1 while the TDRE bit is set to 1. Or wait for NACK (NACKF bit in ICSR register = 1) from the receive
device while the ACKE bit in the ICIER register is set to 1 (when the receive acknowledge bit is set to 1,
transfer is halted). Then, generate a stop condition before setting the TEND bit or the NACKF bit to 0.
Master Transmit Operation
2
C bus Interface Mode).
25. I
2
C bus Interface

Related parts for R5F21334CNFP#U0