R5F21334CNFP#U0 Renesas Electronics America, R5F21334CNFP#U0 Datasheet - Page 464

• Manufacturer Part Number: R5F21334CNFP#U0
• Description: MCU 1KB FLASH 16K ROM 32-LQFP
• Manufacturer: Renesas Electronics America
• Series: R8C/3x/33Cr

Specifications of R5F21334CNFP#U0

• Core Processor: R8C
• Core Size: 16/32-Bit
• Speed: 20MHz
• Connectivity: I²C, LIN, SIO, SSU, UART/USART
• Peripherals: POR, PWM, Voltage Detect, WDT
• Number Of I /o: 27
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Ram Size: 1.5K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 12x10b; D/A 2x8b
• Oscillator Type: Internal
• Operating Temperature: -20°C ~ 85°C
• Package / Case: 32-LQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

R8C/33C Group
REJ09B0570-0100 Rev.1.00 Dec. 14, 2009
Page 434 of 589
25.6
Figure 25.16
Figures 25.16 to 25.19 show Examples of Register Setting When Using I
Examples of Register Setting
Register Setting Example in Master Transmit Mode (I
ICCR1 register
ICCR2 register
ICSR register
ICSR register
ICCR2 register
ICCR1 register
ICSR register
Write transmit data to ICDRT register
Write transmit data to ICDRT register
Write transmit data to ICDRT register
Read ACKBR bit in ICIER register
Read BBSY bit in ICCR2 register
Read TEND bit in ICSR register
Read TDRE bit in ICSR register
Read TEND bit in ICSR register
Read STOP bit in ICSR register
No
No
No
No
No
No
Initial setting
ACKBR = 0?
Yes
BBSY = 0?
TEND = 1?
TDRE = 1?
TEND = 1?
Last byte?
STOP = 1?
Transmit
TDRE bit ← 0
mode?
TEND bit ← 0
TRS bit ← 1
MST bit ← 1
SCP bit ← 0
BBSY bit ← 1
SCP bit ← 0
BBSY bit ← 0
TRS bit ← 0
MST bit ← 0
STOP bit ← 0
Start
End
Yes
Yes
Yes
Yes
Yes
Yes
Yes
No
No
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
(9)
(10)
(11)
(12)
(13)
(14)
(15)
Master receive mode
• Set the STOP bit in the ICSR register to 0.
• Set the IICSEL bit in the SSUIICSR register to 1.
• Set the MSTIIC bit in the MSTCR register to 0.
(1) Determine the state of the SCL and SDA lines.
(2) Set to master transmit mode.
(3) Generate a start condition.
(4) Set the transmit data of the 1st byte
(5) Wait until 1 byte of data is transmitted.
(6) Determine the ACKBR bit from the specified
(7) Set the transmit data after 2nd byte
(8) Wait until the ICRDT register is empty.
(9) Set the transmit data of the last byte.
(10) Wait for end of transmission of the last byte.
(11) Set the TEND bit to 0.
(12) Set the STOP bit to 0.
(13) Generate a stop condition.
(14) Wait until a stop condition is generated.
(15) Set to slave receive mode.
(slave address + R/W).
slave device.
(except the last byte).
Set the TDRE bit to 0.
2
C bus interface.
2
C bus Interface Mode)
25. I
2
C bus Interface