R5F21275SDFP#U0 Renesas Electronics America, R5F21275SDFP#U0 Datasheet - Page 324

• Manufacturer Part Number: R5F21275SDFP#U0
• Description: IC R8C/27 MCU FLASH 32LQFP
• Manufacturer: Renesas Electronics America
• Series: R8C/2x/27r

Specifications of R5F21275SDFP#U0

• Core Processor: R8C
• Core Size: 16/32-Bit
• Speed: 20MHz
• Connectivity: I²C, LIN, SIO, SSU, UART/USART
• Peripherals: LED, POR, Voltage Detect, WDT
• Number Of I /o: 25
• Program Memory Size: 24KB (24K x 8)
• Program Memory Type: FLASH
• Ram Size: 1.5K x 8
• Voltage - Supply (vcc/vdd): 2.2 V ~ 5.5 V
• Data Converters: A/D 12x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 32-LQFP
• For Use With: R0K521276S000BE - KIT DEV RSK-R8C/26-29R0E521000EPB00 - PROBE EMULATOR FOR PC7501
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

R8C/26 Group, R8C/27 Group
Rev.2.10
REJ09B0278-0210
16.3.3.3
In master receive mode, the master device outputs the receive clock, receives data from the slave device, and
returns an acknowledge signal.
Figures 16.34 and 16.35 show the Operating Timing in Master Receive Mode (I
The receive procedure and operation in master receive mode are shown below.
(1) After setting the TEND bit in the ICSR register to 0, switch from master transmit mode to master
(2) When performing the dummy read of the ICDRR register and starting the receive operation, the receive
(3) The 1-frame data receive is completed and the RDRF bit in the ICSR register is set to 1 at the rise of the
(4) Continuous receive operation is enabled by reading the ICDRR register every time the RDRF bit is set
(5) If the next frame is the last receive frame and the RCVD bit in the ICCR1 register is set to 1 (disables
(6) When the RDRF bit is set to 1 at the rise of the 9th clock cycle of the receive clock, generate the stop
(7) When the STOP bit in the ICSR register is set to 1, read the ICDRR register and set the RCVD bit to 0
(8) Return to slave receive mode.
Sep 26, 2008
receive mode by setting the TRS bit in the ICCR1 register to 0. Also, set the TDRE bit in the ICSR
register to 0.
clock is output in synchronization with the internal clock and data is received. The master device
outputs the level set by the ACKBT bit in the ICIER register to the SDA pin at the rising edge of the 9th
clock cycle of the receive clock.
9th clock cycle. At this time, when reading the ICDRR register, the received data can be read and the
RDRF bit is set to 0 simultaneously.
to 1. If the 8th clock cycle falls after the ICDRR register is read by another process while the RDRF bit
is set to 1, the SCL signal is fixed “L” until the ICDRR register is read.
the next receive operation) before reading the ICDRR register, stop condition generation is enabled after
the next receive operation.
condition.
(maintain the following receive operation).
Master Receive Operation
Page 305 of 453
16. Clock Synchronous Serial Interface
2
C bus Interface Mode).