R5F21346CNFP#U0 Renesas Electronics America, R5F21346CNFP#U0 Datasheet - Page 304

• Manufacturer Part Number: R5F21346CNFP#U0
• Description: MCU 1KB FLASH 32K ROM 48-LQFP
• Manufacturer: Renesas Electronics America
• Series: R8C/3x/34Cr

Specifications of R5F21346CNFP#U0

• Core Processor: R8C
• Core Size: 16/32-Bit
• Speed: 20MHz
• Connectivity: I²C, LIN, SIO, SSU, UART/USART
• Peripherals: POR, PWM, Voltage Detect, WDT
• Number Of I /o: 43
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: FLASH
• Ram Size: 2.5K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 12x10b; D/A 2x8b
• Oscillator Type: Internal
• Operating Temperature: -20°C ~ 85°C
• Package / Case: 48-LQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

R8C/34C Group
REJ09B0586-0100 Rev.1.00 Jan 13, 2010
Page 271 of 723
19.3.4
When using the timer mode’s output compare function, the PWM mode, or the PWM2 mode, pulse output from
the TRCIOj (j = A, B, C, or D) output pin can be forcibly cut off and the TRCIOj pin set to function as a
programmable I/O port by means of input to the INT0 pin.
A pin used for output by the timer mode’s output compare function, the PWM mode, or the PWM2 mode can be
set to function as the timer RC output pin by setting the Ej bit in the TRCOER register to 0 (timer RC output
enabled). If “L” is input to the INT0 pin while the PTO bit in the TRCOER register is set to 1 (pulse output
forced cutoff signal input INT0 enabled), bits EA, EB, EC, and ED in the TRCOER register are all set to 1
(timer RC output disabled, TRCIOj output pin functions as the programmable I/O port). When one or two
cycles of the timer RC operation clock after “L” input to the INT0 pin (refer to Table 19.1 Timer RC
Operation Clock) has elapsed, the TRCIOj output pin becomes a programmable I/O port.
Make the following settings to use this function:
• Set the pin state following forced cutoff of pulse output (high impedance (input), “L” output, or “H” output).
• Set the INT0EN bit in the INTEN register to 1 (INT0 input enabled) and the INT0PL bit to 0 (one edge), and
• Set the PD4_5 bit in the PD4 register to 0 (input mode).
• Select the INT0 digital filter by bits INT0F1 to INT0F0 in the INTF register.
• Set the PTO bit in the TRCOER register to 1 (pulse output forced cutoff signal input INT0 enabled).
The IR bit in the INT0IC register is set to 1 (interrupt request) in accordance with the setting of the POL bit in
the INT0IC register and the INT0PL bit in the INTEN register and a change in the INT0 pin input (refer to 11.8
Notes on Interrupts).
For details on interrupts, refer to 11. Interrupts.
(Refer to 7. I/O Ports.)
set the POL bit in the INT0IC register to 0 (falling edge selected).
Forced Cutoff of Pulse Output
19. Timer RC