MC9S08GT60CFD Freescale Semiconductor, MC9S08GT60CFD Datasheet - Page 37

no-image

MC9S08GT60CFD

Manufacturer Part Number
MC9S08GT60CFD
Description
MCU 8BIT 60K FLASH 48-QFN
Manufacturer
Freescale Semiconductor
Series
HCS08r
Datasheet

Specifications of MC9S08GT60CFD

Core Processor
HCS08
Core Size
8-Bit
Speed
40MHz
Connectivity
I²C, SCI, SPI
Peripherals
LVD, POR, PWM, WDT
Number Of I /o
39
Program Memory Size
60KB (60K x 8)
Program Memory Type
FLASH
Ram Size
4K x 8
Voltage - Supply (vcc/vdd)
1.8 V ~ 3.6 V
Data Converters
A/D 8x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
48-QFN Exposed Pad
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
MC9S08GT60CFDE
Manufacturer:
ON
Quantity:
130
Part Number:
MC9S08GT60CFDE
Manufacturer:
FREESCALE
Quantity:
1 831
Part Number:
MC9S08GT60CFDE
Manufacturer:
FREESCALE
Quantity:
20 000
Part Number:
MC9S08GT60CFDE
Manufacturer:
FREESCALE
Quantity:
9 261
the voltage regulator does not enter its low-power standby state but maintains full internal regulation. If
the user attempts to enter either stop1 or stop2 with ENBDM set, the MCU will instead enter stop3.
Most background commands are not available in stop mode. The memory-access-with-status commands
do not allow memory access, but they report an error indicating that the MCU is in either stop or wait
mode. The BACKGROUND command can be used to wake the MCU from stop and enter active
background mode if the ENBDM bit is set. After the device enters background debug mode, all
background commands are available. The table below summarizes the behavior of the MCU in stop when
entry into the background debug mode is enabled.
1
3.6.5
The LVD system is capable of generating either an interrupt or a reset when the supply voltage drops below
the LVD voltage. If the LVD is enabled in stop by setting the LVDE and the LVDSE bits in SPMSC1 when
the CPU executes a STOP instruction, then the voltage regulator remains active during stop mode. If the
user attempts to enter either stop1 or stop2 with the LVD enabled for stop (LVDSE = 1), the MCU will
instead enter stop3. The table below summarizes the behavior of the MCU in stop when the LVD is
enabled.
1
3.6.6
When the MCU enters any stop mode, system clocks to the internal peripheral modules are stopped. Even
in the exception case (ENBDM = 1), where clocks to the background debug logic continue to operate,
clocks to the peripheral systems are halted to reduce power consumption. Refer to
Mode,”
behavior in stop modes.
Freescale Semiconductor
Mode
Stop3
Mode
Stop3
Either ATD stop mode or power-down mode depending on the state of ATDPU.
Either ATD stop mode or power-down mode depending on the state of ATDPU.
Section 3.6.2, “Stop2
Don’t
Don’t
PDC
PDC
care
care
LVD Enabled in Stop Mode
On-Chip Peripheral Modules in Stop Modes
PPDC
PPDC
Don’t
Don’t
care
care
CPU, Digital
Peripherals,
CPU, Digital
Peripherals,
Standby
Standby
FLASH
FLASH
Mode,” and
Table 3-2. BDM Enabled Stop Mode Behavior
Table 3-3. LVD Enabled Stop Mode Behavior
MC9S08GB/GT Data Sheet, Rev. 2.3
Standby
Standby
RAM
RAM
Section 3.6.3, “Stop3
Standby
Active
ICG
ICG
Disabled
Disabled
ATD
ATD
Mode,” for specific information on system
1
1
Regulator
Regulator
Active
Active
Section 3.6.1, “Stop1
I/O Pins
I/O Pins
States
States
held
held
Optionally on
Optionally on
Stop Modes
RTI
RTI
37

Related parts for MC9S08GT60CFD