C8051F018-GQR Silicon Laboratories Inc, C8051F018-GQR Datasheet - Page 130

• Manufacturer Part Number: C8051F018-GQR
• Description: IC 8051 MCU 16K FLASH 64TQFP
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F018r

Specifications of C8051F018-GQR

• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 25MHz
• Connectivity: SMBus (2-Wire/I²C), SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
• Number Of I /o: 32
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Ram Size: 1.25K x 8
• Voltage - Supply (vcc/vdd): 2.8 V ~ 3.6 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-TQFP, 64-VQFP
• Processor Series: C8051F0x
• Core: 8051
• Data Bus Width: 8 bit
• Data Ram Size: 1.25 KB
• Interface Type: I2C, SMBus, SPI, UART
• Maximum Clock Frequency: 25 MHz
• Number Of Programmable I/os: 32
• Number Of Timers: 4 bit
• Operating Supply Voltage: 2.8 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: PK51, CA51, A51, ULINK2
• Development Tools By Supplier: C8051F005DK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

17.2.1. Mode 0: 16-bit Counter/Timer with Capture
In this mode, Timer 2 operates as a 16-bit counter/timer with capture facility. A high-to-low transition on the T2EX
input pin causes the 16-bit value in Timer 2 (TH2, TL2) to be loaded into the capture registers (RCAP2H,
RCAP2L).
Timer 2 can use either SYSCLK, SYSCLK divided by 12, or high-to-low transitions on the external T2 pin as its
clock source when operating in Counter/Timer with Capture mode. Clearing the C/T2 bit (T2CON.1) selects the
system clock as the input for the timer (divided by one or twelve as specified by the Timer Clock Select bit T2M in
CKCON). When C/T2 is set to logic 1, a high-to-low transition at the T2 input pin increments the counter/timer
register. As the 16-bit counter/timer register increments and overflows from 0xFFFF to 0x0000, the TF2 timer
overflow flag (T2CON.7) is set and an interrupt will occur if the interrupt is enabled.
Counter/Timer with Capture mode is selected by setting the Capture/Reload Select bit CP/RL2 (T2CON.0) and the
Timer 2 Run Control bit TR2 (T2CON.2) to logic 1. The Timer 2 External Enable EXEN2 (T2CON.3) must also be
set to logic 1 to enable a capture. If EXEN2 is cleared, transitions on T2EX will be ignored.
SYSCLK
T2EX
T2
Crossbar
Crossbar
EXEN2
12
TR2
0
1
Figure 17.11. T2 Mode 0 Block Diagram
0
1
CKCON
M
T
2
Capture
Rev. 1.2
M
T
1
TCLK
M
T
0
RCAP2L
TL2
RCAP2H
TH2
C8051F018
C8051F019
CP/RL2
EXEN2
TCLK
RCLK
EXF2
C/T2
TR2
TF2
Interrupt
130