C8051F018-GQR Silicon Laboratories Inc, C8051F018-GQR Datasheet - Page 26

• Manufacturer Part Number: C8051F018-GQR
• Description: IC 8051 MCU 16K FLASH 64TQFP
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F018r

Specifications of C8051F018-GQR

• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 25MHz
• Connectivity: SMBus (2-Wire/I²C), SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
• Number Of I /o: 32
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Ram Size: 1.25K x 8
• Voltage - Supply (vcc/vdd): 2.8 V ~ 3.6 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-TQFP, 64-VQFP
• Processor Series: C8051F0x
• Core: 8051
• Data Bus Width: 8 bit
• Data Ram Size: 1.25 KB
• Interface Type: I2C, SMBus, SPI, UART
• Maximum Clock Frequency: 25 MHz
• Number Of Programmable I/os: 32
• Number Of Timers: 4 bit
• Operating Supply Voltage: 2.8 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: PK51, CA51, A51, ULINK2
• Development Tools By Supplier: C8051F005DK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

5.2.
The ADC uses VREF to determine its full-scale voltage, thus the reference must be properly configured before
performing a conversion (see Section 7). The ADC has a maximum conversion speed of 100ksps. The ADC
conversion clock is derived from the system clock. Conversion clock speed can be reduced by a factor of 2, 4, 8 or
16 via the ADCSC bits in the ADC0CF Register. This is useful to adjust conversion speed to accommodate
different system clock speeds.
A conversion can be initiated in one of four ways, depending on the programmed states of the ADC Start of
Conversion Mode bits (ADSTM1, ADSTM0) in ADC0CN. Conversions may be initiated by:
Writing a 1 to ADBUSY provides software control of the ADC whereby conversions are performed “on-demand”.
During conversion, the ADBUSY bit is set to 1 and restored to 0 when conversion is complete. The falling edge of
ADBUSY triggers an interrupt (when enabled) and sets the ADCINT interrupt flag. Note: When conversions are
performed “on-demand”, the ADCINT flag, not ADBUSY, should be polled to determine when the
conversion has completed. Converted data is available in the ADC data word MSB and LSB registers, ADC0H,
ADC0L. Converted data can be either left or right justified in the ADC0H:ADC0L register pair (see example in
Figure 5.9) depending on the programmed state of the ADLJST bit in the ADC0CN register.
The ADCTM bit in register ADC0CN controls the ADC track-and-hold mode. In its default state, the ADC input is
continuously tracked, except when a conversion is in progress. Setting ADCTM to 1 allows one of four different
low power track-and-hold modes to be specified by states of the ADSTM1-0 bits (also in ADC0CN):
Modes 1, 2 and 4 (above) are useful when the start of conversion is triggered with a software command or when the
ADC is operated continuously. Mode 3 is used when the start of conversion is triggered by external hardware. In
this case, the track-and-hold is in its low power mode at times when the CNVSTR input is high. Tracking can also
be disabled (shutdown) when the entire chip is in low power standby or sleep modes.
1. Writing a 1 to the ADBUSY bit of ADC0CN;
2. A Timer 3 overflow (i.e. timed continuous conversions);
3. A rising edge detected on the external ADC convert start signal, CNVSTR;
4. A Timer 2 overflow (i.e. timed continuous conversions).
1. Tracking begins with a write of 1 to ADBUSY and lasts for 3 SAR clocks;
2. Tracking starts with an overflow of Timer 3 and lasts for 3 SAR clocks;
3. Tracking is active only when the CNVSTR input is low;
4. Tracking starts with an overflow of Timer 2 and lasts for 3 SAR clocks.
ADC Modes of Operation
Rev. 1.2
C8051F018
C8051F019
26