C8051F018-GQR Silicon Laboratories Inc, C8051F018-GQR Datasheet - Page 70

• Manufacturer Part Number: C8051F018-GQR
• Description: IC 8051 MCU 16K FLASH 64TQFP
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F018r

Specifications of C8051F018-GQR

• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 25MHz
• Connectivity: SMBus (2-Wire/I²C), SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
• Number Of I /o: 32
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Ram Size: 1.25K x 8
• Voltage - Supply (vcc/vdd): 2.8 V ~ 3.6 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-TQFP, 64-VQFP
• Processor Series: C8051F0x
• Core: 8051
• Data Bus Width: 8 bit
• Data Ram Size: 1.25 KB
• Interface Type: I2C, SMBus, SPI, UART
• Maximum Clock Frequency: 25 MHz
• Number Of Programmable I/os: 32
• Number Of Timers: 4 bit
• Operating Supply Voltage: 2.8 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: PK51, CA51, A51, ULINK2
• Development Tools By Supplier: C8051F005DK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

9.2.
The Flash memory can be used for non-volatile data storage as well as program code. This allows data such as
calibration coefficients to be calculated and stored at run time. Data is written using the MOVX instruction and
read using the MOVC instruction.
9.3.
The CIP-51 provides security options to protect the Flash memory from inadvertent modification by software as
well as prevent the viewing of proprietary program code and constants.
(PSCTL.0) and the Program Store Erase Enable (PSCTL.1) bits protect the Flash memory from accidental
modification by software. These bits must be explicitly set to logic 1 before software can modify the Flash memory.
Additional security features prevent proprietary program code and data constants from being read or altered across
the JTAG interface or by software running on the system controller.
A set of security lock bytes stored at 0x3DFE and 0x3DFF protect the Flash program memory from being read or
altered across the JTAG interface. Each bit in a security lock-byte protects one 4kbyte block of memory. Clearing
a bit to logic 0 in a Read lock byte prevents the corresponding block of Flash memory from being read across the
JTAG interface. Clearing a bit in the Write/Erase lock byte protects the block from JTAG erasures and/or writes.
The Read lock byte is at location 0x3DFF. The Write/Erase lock byte is located at 0x3DFE. Figure 9.2 shows the
location and bit definitions of the security bytes. The 512-byte sector containing the lock bytes can be written to,
but not erased by software. Writing to the reserved area should not be performed.
Bits7-2: UNUSED. Read = 000000b, Write = don’t care.
Bit1:
Bit0:
R/W
Bit7
-
Non-volatile Data Storage
Security Options
Setting this bit allows an entire page of the Flash program memory to be erased provided
the PSWE bit is also set. After setting this bit, a write to Flash memory using the MOVX
instruction will erase the entire page that contains the location addressed by the MOVX
instruction. The value of the data byte written does not matter.
0: Flash program memory erasure disabled.
1: Flash program memory erasure enabled.
Setting this bit allows writing a byte of data to the Flash program memory using the
MOVX instruction. The location must be erased before writing data.
0: Write to Flash program memory disabled.
1: Write to Flash program memory enabled.
PSEE: Program Store Erase Enable.
PSWE: Program Store Write Enable.
R/W
Bit6
-
R/W
Bit5
Figure 9.1. PSCTL: Program Store RW Control
-
R/W
Bit4
-
Rev. 1.2
R/W
Bit3
-
R/W
Bit2
-
The Program Store Write Enable
PSEE
R/W
Bit1
C8051F018
C8051F019
PSWE
R/W
Bit0
SFR Address:
Reset Value
00000000
0x8F
70