MC68HC705C9ACFBE Freescale Semiconductor, MC68HC705C9ACFBE Datasheet - Page 64

• Manufacturer Part Number: MC68HC705C9ACFBE
• Description: IC MCU 8BIT 44-QFP
• Manufacturer: Freescale Semiconductor
• Series: HC05r

Specifications of MC68HC705C9ACFBE

• Core Processor: HC05
• Core Size: 8-Bit
• Speed: 2.1MHz
• Connectivity: SCI, SPI
• Peripherals: POR, WDT
• Number Of I /o: 24
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: OTP
• Ram Size: 352 x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 5.5 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 44-QFP
• Processor Series: HC705C
• Core: HC05
• Data Bus Width: 8 bit
• Data Ram Size: 352 B
• Interface Type: SCI, SPI
• Maximum Clock Frequency: 2.1 MHz
• Number Of Programmable I/os: 31
• Number Of Timers: 1
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8 bit
• Package: 44PQFP
• Family Name: HC05
• Maximum Speed: 2.1 MHz
• Operating Supply Voltage: 3.3|5 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Data Converters: -
• Lead Free Status / Rohs Status: Details

Serial Communications Interface (SCI)
9.11 Start Bit Detection
When the input (idle) line is detected low, it is tested for three more sample times (referred to as the start
edge verification samples in
0, a valid start bit has been detected; otherwise, the line is assumed to be idle. A noise flag is set if all
three verification samples do not detect a logic 0. Thus, a valid start bit could be assumed with a set noise
flag present.
If a framing error has occurred without detection of a break (10 0s for
8-bit format or 11 0s for 9-bit format), the circuit continues to operate as if there actually was a stop bit,
and the start edge will be placed artificially. The last bit received in the data shift register is inverted to a
logic 1, and the three logic 1 start qualifiers (shown in
during the interval when detection of a start bit is anticipated (see
be accepted no sooner than it is anticipated.
If the receiver detects that a break (RDRF = 1, FE = 1, receiver data register = $003B) produced the
framing error, the start bit will not be artificially induced and the receiver must actually detect a logic 1
before the start bit can be recognized (see
64
EXPECTED STOP
RDI
BREAK
Figure 9-6. SCI Artificial Start Following a Frame Error
RDI
RDI
DATA
DATA
MC68HC05C9A Advance Information Data Sheet, Rev. 4.1
Figure
Figure 9-7. SCI Start Bit Following a Break
b) Case 2: Receive line high during expected start edge
a) Case 1: Receive line low during artificial edge
DATA SAMPLES
DATA SAMPLES
DATA SAMPLES
EXPECTED STOP
9-4). If at least two of these three verification samples detect a logic
EXPECTED STOP
Figure
9-7).
Figure
QUALIFIERS
START EDGE
ARTIFICIAL EDGE
START
9-4) are forced into the sample shift register
START BIT
VERIFICATION
Figure
START EDGE
START BIT
SAMPLES
DETECTED AS VALID START EDGE
START BIT
9-6); therefore, the start bit will
DATA
DATA
Freescale Semiconductor