C8051F023-GQR Silicon Laboratories Inc, C8051F023-GQR Datasheet - Page 208

• Manufacturer Part Number: C8051F023-GQR
• Description: IC 8051 MCU 64K FLASH 64TQFP
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F02xr

Specifications of C8051F023-GQR

• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 25MHz
• Connectivity: EBI/EMI, SMBus (2-Wire/I²C), SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
• Number Of I /o: 32
• Program Memory Size: 64KB (64K x 8)
• Program Memory Type: FLASH
• Ram Size: 4.25K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Data Converters: A/D 8x8b, 8x10b; D/A 2x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-TQFP, 64-VQFP
• For Use With: 336-1200 - DEV KIT FOR F020/F021/F022/F023
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

C8051F020/1/2/3
20.1.3. Mode 2: 9-Bit UART, Fixed Baud Rate
Mode 2 provides asynchronous, full-duplex communication using a total of eleven bits per data byte: a start bit, 8 data
bits (LSB first), a programmable ninth data bit, and a stop bit. Mode 2 supports multiprocessor communications and
hardware address recognition (see
the ninth data bit is determined by the value in TB80 (SCON0.3). It can be assigned the value of the parity flag P in
the PSW or used in multiprocessor communications. On receive, the ninth data bit goes into RB80 (SCON0.2) and
the stop bit is ignored.
Data transmission begins when an instruction writes a data byte to the SBUF0 register. The TI0 Transmit Interrupt
Flag (SCON0.1) is set at the end of the transmission (the beginning of the stop-bit time). Data reception can begin
any time after the REN0 Receive Enable bit (SCON0.4) is set to logic 1. After the stop bit is received, the data byte
will be loaded into the SBUF0 receive register if RI0 is logic 0 and one of the following requirements are met:
If the above conditions are satisfied, the eight bits of data are stored in SBUF0, the ninth bit is stored in RB80 and the
RI0 flag is set. If these conditions are not met, SBUF0 and RB80 will not be loaded and the RI0 flag will not be set.
An interrupt will occur if enabled when either TI0 or RI0 is set.
The baud rate in Mode 2 is either SYSCLK / 32 or SYSCLK / 64, depending on the value of the SMOD0 bit in regis-
ter PCON.
208
SPACE
MARK
BIT TIMES
BIT SAMPLING
1.
2.
SM20 is logic 0
SM20 is logic 1, the received 9th bit is logic 1, and the received address matches the UART0 address as
described in
START
BIT
Figure 20.5. UART Modes 2 and 3 Timing Diagram
Section
D0
20.2.
D1
Section “20.2. Multiprocessor Communications” on page
BaudRate
Equation 20.3. Mode 2 Baud Rate
D2
=
D3
2
Rev. 1.4
SMOD0
D4



SYSCLK
--------------------- -
D5
64


D6
D7
210). On transmit,
D8
STOP
BIT