MC68HC11E1CFNE3 Freescale Semiconductor, MC68HC11E1CFNE3 Datasheet - Page 230

IC MCU 8BIT 3MHZ 52-PLCC

MC68HC11E1CFNE3

Manufacturer Part Number
MC68HC11E1CFNE3
Description
IC MCU 8BIT 3MHZ 52-PLCC
Manufacturer
Freescale Semiconductor
Series
HC11r
Datasheets

Specifications of MC68HC11E1CFNE3

Core Processor
HC11
Core Size
8-Bit
Speed
3MHz
Connectivity
SCI, SPI
Peripherals
POR, WDT
Number Of I /o
38
Program Memory Type
ROMless
Eeprom Size
512 x 8
Ram Size
512 x 8
Voltage - Supply (vcc/vdd)
4.5 V ~ 5.5 V
Data Converters
A/D 8x8b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
52-PLCC
Controller Family/series
68HC11
No. Of I/o's
38
Eeprom Memory Size
512Byte
Ram Memory Size
512Byte
Cpu Speed
3MHz
No. Of Timers
1
Embedded Interface Type
SCI, SPI
Rohs Compliant
Yes
Processor Series
HC11E
Core
HC11
Data Bus Width
8 bit
Program Memory Size
512 B
Data Ram Size
512 B
Interface Type
SCI, SPI
Maximum Clock Frequency
3 MHz
Number Of Programmable I/os
22
Number Of Timers
8
Operating Supply Voltage
3 V to 5 V
Maximum Operating Temperature
+ 70 C
Mounting Style
SMD/SMT
Minimum Operating Temperature
0 C
On-chip Adc
8 bit, 8 Channel
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Program Memory Size
-
Lead Free Status / Rohs Status
 Details

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
MC68HC11E1CFNE3
Manufacturer:
NXP
Quantity:
447
Part Number:
MC68HC11E1CFNE3
Manufacturer:
Freescale Semiconductor
Quantity:
10 000
Part Number:
MC68HC11E1CFNE3
Manufacturer:
FREESCALE
Quantity:
20 000
Part Number:
MC68HC11E1CFNE3R
Manufacturer:
ON
Quantity:
5 510
Part Number:
MC68HC11E1CFNE3R
Manufacturer:
PERICOM
Quantity:
5 510
Part Number:
MC68HC11E1CFNE3R
Manufacturer:
Freescale Semiconductor
Quantity:
10 000
To Execute the Program
To Execute the Program
Use this step-by-step procedure to program the MC68HC711E9 device.
Step 1
Step 2
Apply power to the programmer board by moving the +5-V switch to the ON position. From a DOS
command line prompt, start PCbug11this way:
PCbug11 only supports COM ports 1 and 2. If the proper connections are made and you have a
high-quality cable, you should quickly get a PCbug11 command prompt. If you do receive a Comms fault
error, check the cable and board connections. Most PCbug11 communications problems can be traced
to poorly made cables or bad board connections.
Step 3
PCbug11 defaults to base 10 for its input parameters.
Change this to hexadecimal by typing: CONTROL BASE HEX.
Step 4
Clear the block protect register (BPROT) to allow programming of the MC68HC711E9 EEPROM.
At the PCbug11 command prompt, type: MS 1035 00.
230
C:\PCBUG11\ > PCBUG11 –E PORT = 1 with the E9PGMR connected to COM1
C:\PCBUG11\ > PCBUG11 –E PORT = 2 with the E9PGMR connected to COM2
Enabling the Security Feature on the MC68HC711E9 Devices with PCbug11 on the M68HC711E9PGMR, Rev. 0.1
Before applying power to the programming board, connect the M68HC711E9PGMR serial port P2
to one of your PC COM ports with a standard 25-pin RS-232 cable. Do not use a null modem cable
or adapter which swaps the transmit and receive signals between the connectors at each end of
the cable.
Place the MC68HC711E9 part in the PLCC socket on your board.
Insert the part upside down with the notched corner pointing toward the red power LED.
Make sure both S1 and S2 switches are turned off.
Apply +5 volts to +5-V, +12 volts (at most +12.5 volts) to V
programmer board’s power connector, P1. The remaining TXD/PD1 and RXD/PD0 connections
are not used in this procedure. They are for gang programming MC68HC711E9 devices, which is
discussed in the M68HC711E9PGMR Manual. You cannot gang program with PCbug11.
Ensure that the "remove for multi-programming" jumper, J1, below the +5-V power switch has a
fabricated jumper installed.
or
PP
, and ground to GND on your
Freescale Semiconductor

Related parts for MC68HC11E1CFNE3