MC68HC11E1VFNE3 Freescale Semiconductor, MC68HC11E1VFNE3 Datasheet - Page 62

• Manufacturer Part Number: MC68HC11E1VFNE3
• Description: MCU 8-BIT 512 RAM 3MHZ 52-PLCC
• Manufacturer: Freescale Semiconductor
• Series: HC11r

Specifications of MC68HC11E1VFNE3

• Core Processor: HC11
• Core Size: 8-Bit
• Speed: 3MHz
• Connectivity: SCI, SPI
• Peripherals: POR, WDT
• Number Of I /o: 38
• Program Memory Type: ROMless
• Eeprom Size: 512 x 8
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 4.5 V ~ 5.5 V
• Data Converters: A/D 8x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 105°C
• Package / Case: 52-PLCC
• Processor Series: HC11E
• Core: HC11
• Data Bus Width: 8 bit
• Data Ram Size: 512 B
• Interface Type: SCI, SPI
• Maximum Clock Frequency: 3 MHz
• Number Of Programmable I/os: 38
• Number Of Timers: 8
• Maximum Operating Temperature: + 105 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8 bit, 8 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Program Memory Size: -
• Lead Free Status / Rohs Status: Details

Analog-to-Digital (A/D) Converter
3.7 Multiple-Channel Operation
The two types of multiple-channel operation are:
3.8 Operation in Stop and Wait Modes
If a conversion sequence is in progress when either the stop or wait mode is entered, the conversion of
the current channel is suspended. When the MCU resumes normal operation, that channel is resampled
and the conversion sequence is resumed. As the MCU exits wait mode, the A/D circuits are stable and
valid results can be obtained on the first conversion. However, in stop mode, all analog bias currents are
disabled and it is necessary to allow a stabilization period when leaving stop mode. If stop mode is exited
with a delay (DLY = 1), there is enough time for these circuits to stabilize before the first conversion. If
stop mode is exited with no delay (DLY bit in OPTION register = 0), allow 10 ms for the A/D circuitry to
stabilize to avoid invalid results.
3.9 A/D Control/Status Register
All bits in this register can be read or written, except bit 7, which is a read-only status indicator, and bit 6,
which always reads as 0. Write to ADCTL to initiate a conversion. To quit a conversion in progress, write
to this register and a new conversion sequence begins immediately.
CCF — Conversion Complete Flag
Bit 6 — Unimplemented
SCAN — Continuous Scan Control Bit
62
1. When SCAN = 0, a selected group of four channels is converted one time each. The first result is
2. When SCAN = 1, conversions continue to be performed on the selected group of channels with the
A read-only status indicator, this bit is set when all four A/D result registers contain valid conversion
results. Each time the ADCTL register is overwritten, this bit is automatically cleared to 0 and a
conversion sequence is started. In the continuous mode, CCF is set at the end of the first conversion
sequence.
Always reads 0
stored in A/D result register 1 (ADR1), and the fourth result is stored in ADR4. After the fourth
conversion is complete, all conversion activity is halted until a new conversion command is written
to the ADCTL register.
fifth conversion being stored in register ADR1 (replacing the earlier conversion result for the first
channel in the group), the sixth conversion overwriting ADR2, and so on.
Address: $1030
Reset:
Read:
Write:
CCF
Bit 7
0
Figure 3-5. A/D Control/Status Register (ADCTL)
= Unimplemented
6
0
M68HC11E Family Data Sheet, Rev. 5.1
SCAN
5
MULT
4
Indeterminate after reset
CD
3
CC
2
CB
1
Freescale Semiconductor
Bit 0
CA