M30626SPGP#U3C Renesas Electronics America, M30626SPGP#U3C Datasheet - Page 68

• Manufacturer Part Number: M30626SPGP#U3C
• Description: IC M16C/62P MCU ROMLESS 100LQFP
• Manufacturer: Renesas Electronics America
• Series: M16C™ M16C/60r

Specifications of M30626SPGP#U3C

• Core Processor: M16C/60
• Core Size: 16-Bit
• Speed: 24MHz
• Connectivity: I²C, IEBus, UART/USART
• Peripherals: DMA, WDT
• Number Of I /o: 50
• Program Memory Type: ROMless
• Ram Size: 31K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 26x10b; D/A 2x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-LQFP
• For Use With: 867-1000 - KIT QUICK START RENESAS 62PR0K33062PS001BE - R0K33062P STARTER KITR0K33062PS000BE - KIT EVAL STARTER FOR M16C/62PM3062PT3-CPE-3 - EMULATOR COMPACT M16C/62P/30P
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Program Memory Size: -

M16C/62P Group (M16C/62P, M16C/62PT)
Rev.2.41
REJ09B0185-0241
6.2
6.3
bit in the CM1 register is set to “1” under the conditions below.
If the microcomputer is set to enter stop mode when the voltage applied to the VCC1 pin drops below Vdet4 and to
exit stop mode when the voltage applied rises to Vdet4 or above, set the CM10 bit to “1” when VC13 bit is “0”
(VCC1 < Vdet4).
The low voltage detection interrupt is immediately generated and the microcomputer exits wait mode If WAIT
instruction is executed under the conditions below.
If the microcomputer is set to enter wait mode when the voltage applied to the VCC1 pin drops below Vdet4 and to
exit wait mode when the voltage applied rises to Vdet4 or above, perform WAIT instruction when VC13 bit is “0”
(VCC1 < Vdet4).
The low voltage detection interrupt is immediately generated and the microcomputer exits stop mode if the CM10
•
•
•
•
•
•
•
•
•
the VC27 bit in the VCR2 register is set to “1” (low voltage detection circuit enabled),
the D40 bit in the D4INT register is set to “1” (low voltage detection interrupt enabled),
the D41 bit in the D4INT register is set to “1” (low voltage detection interrupt is used to exit stop mode), and
the voltage applied to the VCC1 pin is higher than Vdet4 (the VC13 bit in the VCR1 register is “1”)
the CM02 bit in the CM0 register is set to “1” (stop peripheral function clock),
the VC27 bit in the VCR2 register is set to “1” (low voltage detection circuit enabled),
the D40 bit in the D4INT register is set to “1” (low voltage detection interrupt enabled),
the D41 bit in the D4INT register is set to “1” (low voltage detection interrupt is used to exit wait mode), and
the voltage applied to the VCC1 pin is higher than Vdet4 (the VC13 bit in the VCR1 register is “1”)
Limitations on Exiting Wait Mode
Jan 10, 2006
Limitations on Exiting Stop Mode
Page 51 of 390
6. Voltage Detection Circuit