HD64F2638F20J Renesas Electronics America, HD64F2638F20J Datasheet - Page 652

• Manufacturer Part Number: HD64F2638F20J
• Description: IC H8S MCU FLASH 256K 128-QFP
• Manufacturer: Renesas Electronics America
• Series: H8® H8S/2600r

Specifications of HD64F2638F20J

• Core Processor: H8S/2600
• Core Size: 16-Bit
• Speed: 20MHz
• Connectivity: CAN, SCI, SmartCard
• Peripherals: Motor Control PWM, POR, PWM, WDT
• Number Of I /o: 72
• Program Memory Size: 256KB (256K x 8)
• Program Memory Type: FLASH
• Ram Size: 16K x 8
• Voltage - Supply (vcc/vdd): 4.5 V ~ 5.5 V
• Data Converters: A/D 12x10b; D/A 2x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 128-QFP
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -

Section 15 I
(Only for the H8S/2638, H8S/2639, and H8S/2630)
Item
t
Notes: 1. Does not meet the I
• Note on ICDR Read at End of Master Reception
Page 602 of 1458
SDAHO
To halt reception at the end of a receive operation in master receive mode, set the TRS bit to 1
and write 0 to BBSY and SCP in ICCR. This changes SDA from low to high when SCL is
high, and generates the stop condition. After this, receive data can be read by means of an
ICDR read, but if data remains in the buffer the ICDRS receive data will not be transferred to
ICDR, and so it will not be possible to read the second byte of data.
If it is necessary to read the second byte of data, issue the stop condition in master receive
mode (i.e. with the TRS bit cleared to 0). When reading the receive data, first confirm that the
BBSY bit in the ICCR register is cleared to 0, the stop condition has been generated, and the
bus has been released, then read the ICDR register with TRS cleared to 0.
Note that if the receive data (ICDR data) is read in the interval between execution of the
instruction for issuance of the stop condition (writing of 0 to BBSY and SCP in ICCR) and the
actual generation of the stop condition, the clock may not be output correctly in subsequent
master transmission.
Clearing of the MST bit after completion of master transmission/reception, or other
modifications of IIC control bits to change the transmit/receive operating mode or settings,
must be carried out during interval (a) in figure 15-18 (after confirming that the BBSY bit has
been cleared to 0 in the ICCR register).
t
Indication
3 t
cyc
2. Calculated using the I
cyc
2
C Bus Interface [Option]
is necessary: (a) secure a start/stop condition issuance interval; (b) adjust the rise and
fall times by means of a pull-up resistor and capacitive load; (c) reduce the transfer rate;
(d) select slave devices whose input timing permits this output timing.
The values in the above table will vary depending on the settings of the IICX bit and bits
CKS0 to CKS2. Depending on the frequency it may not be possible to achieve the
maximum transfer rate; therefore, whether or not the I
met must be determined in accordance with the actual setting conditions.
speed mode: 1300 ns min.).
Standard
mode
High-speed
mode
t
Influence
(Max.)
0
0
Sr
2
C bus interface specification. Remedial action such as the following
/t
2
Sf
C bus specification values (standard mode: 4700 ns min.; high-
Time Indication (at Maximum Transfer Rate) [ns]
I
Specifi-
cation
(Min.)
0
0
2
C Bus
φ =
5 MHz
600
600
φ =
8 MHz
375
375
2
C bus interface specifications are
300
300
φ =
10 MHz
H8S/2639, H8S/2638, H8S/2636,
REJ09B0103-0800 Rev. 8.00
H8S/2630, H8S/2635 Group
φ =
16 MHz
188
188
May 28, 2010
φ =
20 MHz
150
150