IC MCU 128K 6MHZ A/D IT 64TQFP

ATMEGA103-6AI

Manufacturer Part NumberATMEGA103-6AI
DescriptionIC MCU 128K 6MHZ A/D IT 64TQFP
ManufacturerAtmel
SeriesAVR® ATmega
ATMEGA103-6AI datasheets
 


Specifications of ATMEGA103-6AI

Core ProcessorAVRCore Size8-Bit
Speed6MHzConnectivitySPI, UART/USART
PeripheralsPOR, PWM, WDTNumber Of I /o32
Program Memory Size128KB (64K x 16)Program Memory TypeFLASH
Eeprom Size4K x 8Ram Size4K x 8
Voltage - Supply (vcc/vdd)4 V ~ 5.5 VData ConvertersA/D 8x10b
Oscillator TypeInternalOperating Temperature-40°C ~ 85°C
Package / Case64-TQFP, 64-VQFPFor Use WithATSTK501 - ADAPTER KIT FOR 64PIN AVR MCU
Lead Free Status / RoHS StatusContains lead / RoHS non-compliant  
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
Page 61
62
Page 62
63
Page 63
64
Page 64
65
Page 65
66
Page 66
67
Page 67
68
Page 68
69
Page 69
70
Page 70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
Page 70/141

Download datasheet (3Mb)Embed
PrevNext
UART Control
UART I/O Data Register – UDR
UART Status Register – USR
ATmega103(L)
70
Bit
7
6
5
$0C ($2C)
MSB
Read/Write
R/W
R/W
R/W
Initial Value
0
0
0
The UDR Register is actually two physically separate registers sharing the same I/O
address. When writing to the register, the UART Transmit Data Register is written.
When reading from UDR, the UART Receive Data Register is read.
Bit
7
6
5
$0B ($2B)
RXC
TXC
UDRE
Read/Write
R
R/W
R
Initial Value
0
0
1
The USR Register is a read-only register providing information on the UART Status.
• Bit 7 – RXC: UART Receive Complete
This bit is set (one) when a received character is transferred from the Receiver Shift
Register to UDR. The bit is set regardless of any detected framing errors. When the
RXCIE bit in UCR is set, the UART Receive Complete interrupt will be executed when
RXC is set (one). RXC is cleared by reading UDR. When interrupt-driven data reception
is used, the UART Receive Complete Interrupt routine must read UDR in order to clear
RXC, otherwise a new interrupt will occur once the interrupt routine terminates.
• Bit 6 – TXC: UART Transmit Complete
This bit is set (one) when the entire character (including the stop bit) in the Transmit
Shift Register has been shifted out and no new data has been written to the UDR. This
flag is especially useful in half-duplex communications interfaces, where a transmitting
application must enter Receive mode and free the communications bus immediately
after completing the transmission.
When the TXCIE bit in UCR is set, setting of TXC causes the UART Transmit Complete
interrupt to be executed. TXC is cleared by hardware when executing the corresponding
interrupt handling vector. Alternatively, the TXC bit is cleared (zero) by writing a logical
“1” to the bit.
• Bit 5 – UDRE: UART Data Register Empty
This bit is set (one) when a character written to UDR is transferred to the Transmit Shift
Register. Setting of this bit indicates that the Transmitter is ready to receive a new char-
acter for transmission.
When the UDRIE bit in UCR is set, the UART Transmit Complete interrupt to be exe-
cuted as long as UDRE is set. UDRE is cleared by writing UDR. When interrupt-driven
data transmittal is used, the UART Data Register Empty Interrupt routine must write
UDR in order to clear UDRE, otherwise a new interrupt will occur once the interrupt rou-
tine terminates.
UDRE is set (one) during reset to indicate that the Transmitter is ready.
4
3
2
1
0
LSB
R/W
R/W
R/W
R/W
R/W
0
0
0
0
0
4
3
2
1
0
FE
OR
R
R
R
R
R
0
0
0
0
0
UDR
USR
0945I–AVR–02/07