ATMEGA88-20MU Atmel, ATMEGA88-20MU Datasheet - Page 61

• Manufacturer Part Number: ATMEGA88-20MU
• Description: IC AVR MCU 8K 20MHZ 5V 32-QFN
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA88-20MU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 23
• Program Memory Size: 8KB (4K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 512 x 8
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 32-VQFN Exposed Pad, 32-HVQFN, 32-SQFN, 32-DHVQFN
• Package: 32MLF EP
• Device Core: AVR
• Family Name: ATmega
• Maximum Speed: 20 MHz
• Operating Supply Voltage: 3.3|5 V
• Data Bus Width: 8 Bit
• Number Of Programmable I/os: 23
• Interface Type: SPI/TWI/USART
• On-chip Adc: 8-chx10-bit
• Number Of Timers: 3
• Processor Series: ATMEGA8x
• Core: AVR8
• Data Ram Size: 1 KB
• Maximum Clock Frequency: 20 MHz
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500, ATSTK600, ATAVRISP2, ATAVRONEKIT, ATAVRTS2080A, ATASTK512-EK1-IND
• Minimum Operating Temperature: - 40 C
• A/d Inputs: 8-Channel, 10-Bit
• Cpu Speed: 20 MIPS
• Eeprom Memory: 512 Bytes
• Input Output: 23
• Interface: SPI/TWI/USART
• Memory Type: Flash
• Number Of Bits: 8
• Package Type: 32-pin MLF
• Programmable Memory: 8K Bytes
• Timers: 2-8-bit, 1-16-bit
• Voltage, Range: 4.5-5.5 V
• Controller Family/series: AVR MEGA
• No. Of I/o's: 23
• Eeprom Memory Size: 512Byte
• Ram Memory Size: 1KB
• No. Of Timers: 3
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

2545S–AVR–07/10
Table 11-5
BOOTRST and IVSEL settings. If the program never enables an interrupt source, the Interrupt
Vectors are not used, and regular program code can be placed at these locations. This is also
the case if the Reset Vector is in the Application section while the Interrupt Vectors are in the
Boot section or vice versa.
Table 11-5.
Note:
The most typical and general program setup for the Reset and Interrupt Vector Addresses in
ATmega168 is:
BOOTRST
Address Labels Code
0x0000
0x0002
0x0004
0x0006
0x0008
0x000A
0x000C
0x000E
0x0010
0x0012
0x0014
0x0016
0x0018
0x001A
0x001C
0x001E
0x0020
0x0022
0x0024
0x0026
0x0028
0x002A
0x002C
0x002E
0x0030
0x0032
1
1
0
0
2. When the IVSEL bit in MCUCR is set, Interrupt Vectors will be moved to the start of the Boot
1. The Boot Reset Address is shown in
Flash Section. The address of each Interrupt Vector will then be the address in this table
added to the start address of the Boot Flash Section.
means unprogrammed while “0” means programmed.
shows reset and Interrupt Vectors placement for the various combinations of
Reset and Interrupt Vectors Placement in ATmega168
IVSEL
0
1
0
1
jmp
jmp
jmp
jmp
jmp
jmp
jmp
jmp
jmp
jmp
jmp
jmp
jmp
jmp
jmp
jmp
jmp
jmp
jmp
jmp
jmp
jmp
jmp
jmp
jmp
jmp
Reset Address
0x000
0x000
Boot Reset Address
Boot Reset Address
RESET
EXT_INT0
EXT_INT1
PCINT0
PCINT1
PCINT2
WDT
TIM2_COMPA
TIM2_COMPB
TIM2_OVF
TIM1_CAPT
TIM1_COMPA
TIM1_COMPB
TIM1_OVF
TIM0_COMPA
TIM0_COMPB
TIM0_OVF
SPI_STC
USART_RXC
USART_UDRE
USART_TXC
ADC
EE_RDY
ANA_COMP
TWI
SPM_RDY
Table 26-6 on page
Comments
; Reset Handler
; IRQ0 Handler
; IRQ1 Handler
; PCINT0 Handler
; PCINT1 Handler
; PCINT2 Handler
; Watchdog Timer Handler
; Timer2 Compare A Handler
; Timer2 Compare B Handler
; Timer2 Overflow Handler
; Timer1 Capture Handler
; Timer1 Compare A Handler
; Timer1 Compare B Handler
; Timer1 Overflow Handler
; Timer0 Compare A Handler
; Timer0 Compare B Handler
; Timer0 Overflow Handler
; SPI Transfer Complete Handler
; USART, RX Complete Handler
; USART, UDR Empty Handler
; USART, TX Complete Handler
; ADC Conversion Complete Handler
; EEPROM Ready Handler
; Analog Comparator Handler
; 2-wire Serial Interface Handler
; Store Program Memory Ready Handler
Interrupt Vectors Start Address
0x001
Boot Reset Address + 0x0002
0x001
Boot Reset Address + 0x0002
ATmega48/88/168
280. For the BOOTRST Fuse “1”
(1)
61