ATMEGA88-20PU Atmel, ATMEGA88-20PU Datasheet - Page 62

• Manufacturer Part Number: ATMEGA88-20PU
• Description: IC AVR MCU 8K 20MHZ 5V 28DIP
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA88-20PU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 23
• Program Memory Size: 8KB (4K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 512 x 8
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 6x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-DIP (0.300", 7.62mm)
• Cpu Family: ATmega
• Device Core: AVR
• Device Core Size: 8b
• Frequency (max): 20MHz
• Interface Type: SPI/TWI/USART
• Total Internal Ram Size: 1KB
• # I/os (max): 23
• Number Of Timers - General Purpose: 3
• Operating Supply Voltage (typ): 3.3/5V
• Operating Supply Voltage (max): 5.5V
• Operating Supply Voltage (min): 2.7V
• On-chip Adc: 6-chx10-bit
• Instruction Set Architecture: RISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Through Hole
• Pin Count: 28
• Package Type: PDIP
• Processor Series: ATMEGA8x
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 1 KB
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 23
• Number Of Timers: 3
• Operating Supply Voltage: 2.7 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500, ATSTK600, ATAVRISP2, ATAVRONEKIT, ATAVRTS2080A, ATASTK512-EK1-IND
• Minimum Operating Temperature: - 40 C
• Package: 28PDIP
• Family Name: ATmega
• Maximum Speed: 20 MHz
• For Use With: ATAVRDRAGON - KIT DRAGON 32KB FLASH MEM AVRATAVRISP2 - PROGRAMMER AVR IN SYSTEM
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

62
ATmega48/88/168
When the BOOTRST Fuse is unprogrammed, the Boot section size set to 2 Kbytes and the
IVSEL bit in the MCUCR Register is set before any interrupts are enabled, the most typical and
general program setup for the Reset and Interrupt Vector Addresses in ATmega168 is:
When the BOOTRST Fuse is programmed and the Boot section size set to 2 Kbytes, the most
typical and general program setup for the Reset and Interrupt Vector Addresses in ATmega168
is:
When the BOOTRST Fuse is programmed, the Boot section size set to 2 Kbytes and the IVSEL
bit in the MCUCR Register is set before any interrupts are enabled, the most typical and general
program setup for the Reset and Interrupt Vector Addresses in ATmega168 is:
;
0x0033RESET:
0x0034
0x0035
0x0036
0x0037
0x0038
Address Labels Code
0x0000
0x0001
0x0002
0x0003
0x0004
0x0005
;
.org 0xC02
0x1C02
0x1C04
...
0x1C32
Address Labels Code
.org 0x0002
0x0002
0x0004
...
0x0032
;
.org 0x1C00
0x1C00
0x1C01
0x1C02
0x1C03
0x1C04
0x1C05
...
RESET: ldi
RESET: ldi
...
ldi
out
ldi
out
sei
<instr>
out
ldi
out
sei
<instr>
jmp
jmp
...
jmp
jmp
jmp
...
jmp
out
ldi
out
sei
<instr>
...
...
r16, high(RAMEND); Main program start
SPH,r16
r16, low(RAMEND)
SPL,r16
r16,high(RAMEND); Main program start
SPH,r16
r16,low(RAMEND)
SPL,r16
EXT_INT0
EXT_INT1
...
SPM_RDY
EXT_INT0
EXT_INT1
...
SPM_RDY
r16,high(RAMEND); Main program start
SPH,r16
r16,low(RAMEND)
SPL,r16
xxx
xxx
xxx
Comments
; Set Stack Pointer to top of RAM
; Enable interrupts
Comments
; Set Stack Pointer to top of RAM
; Enable interrupts
; IRQ0 Handler
; IRQ1 Handler
;
; Store Program Memory Ready Handler
; IRQ0 Handler
; IRQ1 Handler
;
; Store Program Memory Ready Handler
; Set Stack Pointer to top of RAM
; Enable interrupts
2545S–AVR–07/10