STM32F101T6U6 STMicroelectronics, STM32F101T6U6 Datasheet - Page 33

• Manufacturer Part Number: STM32F101T6U6
• Description: MCU 32BIT ARM 32K FLASH 36VFQFPN
• Manufacturer: STMicroelectronics
• Series: STM32r

Specifications of STM32F101T6U6

• Core Processor: ARM® Cortex-M3™
• Core Size: 32-Bit
• Speed: 36MHz
• Connectivity: I²C, IrDA, LIN, SPI, UART/USART
• Peripherals: DMA, PDR, POR, PVD, PWM, Temp Sensor, WDT
• Number Of I /o: 26
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: FLASH
• Ram Size: 6K x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 3.6 V
• Data Converters: A/D 10x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 36-VFQFN, 36-VFQFPN
• For Use With: KSDKSTM32-PL - KIT IAR KICKSTART STM32 CORTEXM3497-8512 - KIT STARTER FOR STM32F10XE MCU497-8505 - KIT STARTER FOR STM32F10XE MCU497-8304 - KIT STM32 MOTOR DRIVER BLDC497-6289 - KIT PERFORMANCE STICK FOR STM32MCBSTM32UME - BOARD EVAL MCBSTM32 + ULINK-MEMCBSTM32U - BOARD EVAL MCBSTM32 + ULINK2497-6053 - KIT STARTER FOR STM32497-6052 - KIT STARTER FOR STM32497-6050 - KIT STARTER FOR STM32497-6049 - KIT EVALUATION LOW COST STM32497-6048 - BOARD EVALUATION FOR STM32497-6047 - KIT DEVELOPMENT FOR STM32
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

STM32F101x4, STM32F101x6
5.3.4
5.3.5
Embedded reference voltage
The parameters given in
temperature and V
Table 11.
1. Shortest sampling time can be determined in the application by multiple iterations.
2. Guaranteed by design, not tested in production.
Supply current characteristics
The current consumption is a function of several parameters and factors such as the
operating voltage, ambient temperature, I/O pin loading, device software configuration,
operating frequencies, I/O pin switching rate, program location in memory and executed
binary code.
The current consumption is measured as described in
measurement
All Run-mode current consumption measurements given in this section are performed with a
reduced code that gives a consumption equivalent to Dhrystone 2.1 code.
Maximum current consumption
The MCU is placed under the following conditions:
●
●
●
●
●
The parameters given in
temperature and V
T
V
Symbol
V
S_vrefint
T
RERINT
REFINT
Coeff
All I/O pins are in input mode with a static value at V
All peripherals are disabled except if it is explicitly mentioned
The Flash access time is adjusted to f
wait state from 24 to 36 MHz)
Prefetch in on (reminder: this bit must be set before clock setting and bus prescaling)
When the peripherals are enabled f
(2)
(2)
(1)
Internal reference voltage
ADC sampling time when reading
the internal reference voltage
Internal reference voltage spread
over the temperature range
Temperature coefficient
Embedded internal reference voltage
scheme.
DD
DD
supply voltage conditions summarized in
Parameter
supply voltage conditions summarized in
Table 11
Table 12
Doc ID 15058 Rev 5
are derived from tests performed under the ambient
are derived from tests performed under the ambient
PCLK1
HCLK
–40 °C < T
V
DD
= f
Conditions
frequency (0 wait state from 0 to 24 MHz, 1
= 3 V ±10 mV
HCLK/2
A
Figure 11: Current consumption
< +85 °C 1.16
, f
DD
PCLK2
or V
Table
Table
= f
SS
Electrical characteristics
Min
HCLK
(no load)
8.
8.
1.20
Typ
5.1
17.1
Max
1.24
100
10
(2)
ppm/
Unit
33/79
mV
µs
°C
V