STM32F101T6U6 STMicroelectronics, STM32F101T6U6 Datasheet - Page 59

• Manufacturer Part Number: STM32F101T6U6
• Description: MCU 32BIT ARM 32K FLASH 36VFQFPN
• Manufacturer: STMicroelectronics
• Series: STM32r

Specifications of STM32F101T6U6

• Core Processor: ARM® Cortex-M3™
• Core Size: 32-Bit
• Speed: 36MHz
• Connectivity: I²C, IrDA, LIN, SPI, UART/USART
• Peripherals: DMA, PDR, POR, PVD, PWM, Temp Sensor, WDT
• Number Of I /o: 26
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: FLASH
• Ram Size: 6K x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 3.6 V
• Data Converters: A/D 10x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 36-VFQFN, 36-VFQFPN
• For Use With: KSDKSTM32-PL - KIT IAR KICKSTART STM32 CORTEXM3497-8512 - KIT STARTER FOR STM32F10XE MCU497-8505 - KIT STARTER FOR STM32F10XE MCU497-8304 - KIT STM32 MOTOR DRIVER BLDC497-6289 - KIT PERFORMANCE STICK FOR STM32MCBSTM32UME - BOARD EVAL MCBSTM32 + ULINK-MEMCBSTM32U - BOARD EVAL MCBSTM32 + ULINK2497-6053 - KIT STARTER FOR STM32497-6052 - KIT STARTER FOR STM32497-6050 - KIT STARTER FOR STM32497-6049 - KIT EVALUATION LOW COST STM32497-6048 - BOARD EVALUATION FOR STM32497-6047 - KIT DEVELOPMENT FOR STM32
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

STM32F101x4, STM32F101x6
Table 39.
1. Guaranteed by design, not tested in production.
2. f
3. The maximum hold time of the Start condition has only to be met if the interface does not stretch the low
4. The device must internally provide a hold time of at least 300 ns for the SDA signal in order to bridge the
t
w(STO:STA)
Symbol
t
t
t
t
t
w(SCLH)
t
w(SCLL)
t
su(SDA)
t
t
t
su(STO)
t
su(STA)
h(SDA)
4 MHz to achieve fast mode I
maximum I2C fast mode clock.
period of SCL signal.
undefined region of the falling edge of SCL.
h(STA)
r(SDA)
r(SCL)
f(SDA)
f(SCL)
PCLK1
C
b
must be higher than 2 MHz to achieve standard mode I
SCL clock low time
SCL clock high time
SDA setup time
SDA data hold time
SDA and SCL rise time
SDA and SCL fall time
Start condition hold time
Repeated Start condition setup
time
Stop condition setup time
Stop to Start condition time (bus
free)
Capacitive load for each bus line
I
2
C characteristics
Parameter
2
C frequencies. It must be a multiple of 10 MHz to reach the 400 kHz
Doc ID 15058 Rev 5
Standard mode I
Min
250
0
4.7
4.0
4.0
4.7
4.0
4.7
(3)
2
C frequencies. It must be higher than
1000
Max
300
400
2
C
(1)
Electrical characteristics
Fast mode I
20+0.1C
Min
100
0
1.3
0.6
0.6
0.6
1.3
0.6
(4)
b
2
900
Max
C
300
300
400
(1)(2)
(3)
Unit
59/79
pF
µs
ns
µs
µs
µs