MC68HC11E1CFN3 Freescale Semiconductor, MC68HC11E1CFN3 Datasheet - Page 53

• Manufacturer Part Number: MC68HC11E1CFN3
• Description: IC MCU 3MHZ 512 EEPROM 52-PLCC
• Manufacturer: Freescale Semiconductor
• Series: HC11r

Specifications of MC68HC11E1CFN3

• Core Processor: HC11
• Core Size: 8-Bit
• Speed: 3MHz
• Connectivity: SCI, SPI
• Peripherals: POR, WDT
• Number Of I /o: 38
• Program Memory Type: ROMless
• Eeprom Size: 512 x 8
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 4.5 V ~ 5.5 V
• Data Converters: A/D 8x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 52-PLCC
• Data Bus Width: 8 bit
• Data Ram Size: 512 B
• Interface Type: SCI, SPI
• Maximum Clock Frequency: 3 MHz
• Number Of Programmable I/os: 22
• Number Of Timers: 16 bit
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8 bit
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Program Memory Size: -
• Lead Free Status / Rohs Status: Details

2.4.1 Programming an Individual EPROM Address
M68HC11E Family — Rev. 5
MOTOROLA
NOTE:
Using the on-chip EPROM/OTPROM programming feature requires an external
12-volt nominal power supply (V
the EPROM/OTPROM programming register (PPROG).
PPROG is the combined EPROM/OTPROM and EEPROM programming register
on all devices with EPROM/OTPROM except the MC68HC711E20. For the
MC68HC711E20, there is a separate register for EPROM/OTPROM programming
called the EPROG register.
As described in the following subsections, these two methods of programming and
verifying EPROM are possible:
In this method, the MCU programs its own EPROM by controlling the PPROG
register (EPROG in MC68HC711E20). Use these procedures to program the
EPROM through the MCU with:
Any operating mode can be used.
This example applies to all devices with EPROM/OTPROM except for the
MC68HC711E20.
This example applies only to MC68HC711E20.
1. Programming an individual EPROM address
2. Programming the EPROM with downloaded data
•
•
•
EPROG
EPROG
The ROMON bit set in the CONFIG register
The 12-volt nominal programming voltage present on the XIRQ/V
The IRQ pin must be pulled high.
Freescale Semiconductor, Inc.
For More Information On This Product,
LDAB
STAB
STAA
LDAB
STAB
JSR
CLR
LDAB
STAB
STAA
LDAB
STAB
JSR
CLR
Operating Modes and On-Chip Memory
Go to: www.freescale.com
#$20
$103B
$0,X
#$21
$103B
DLYEP
$103B
#$20
$1036
$0,X
#$21
$1036
DLYEP
$1036
Set ELAT bit in (EPGM = 0) to enable
EPROM latches.
Store data to EPROM address
Set EPGM bit with ELAT = 1 to enable
EPROM programming voltage
Delay 2–4 ms
Turn off programming voltage and set
to READ mode
Set ELAT bit (EPGM = 0) to enable
EPROM latches.
Store data to EPROM address
Set EPGM bit with ELAT = 1 to enable
EPROM programming voltage
Delay 2–4 ms
Turn off programming voltage and set
to READ mode
PPE
). Normal programming is accomplished using
Operating Modes and On-Chip Memory
EPROM/OTPROM
PPE
Data Sheet
pin
53