MC68HC711E20CFN4 Freescale Semiconductor, MC68HC711E20CFN4 Datasheet - Page 57

no-image

MC68HC711E20CFN4

Manufacturer Part Number
MC68HC711E20CFN4
Description
IC MCU 20K OTP 4MHZ 52-PLCC
Manufacturer
Freescale Semiconductor
Series
HC11r
Datasheets

Specifications of MC68HC711E20CFN4

Core Processor
HC11
Core Size
8-Bit
Speed
4MHz
Connectivity
SCI, SPI
Peripherals
POR, WDT
Number Of I /o
38
Program Memory Size
20KB (20K x 8)
Program Memory Type
OTP
Eeprom Size
512 x 8
Ram Size
768 x 8
Voltage - Supply (vcc/vdd)
4.5 V ~ 5.5 V
Data Converters
A/D 8x8b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
52-PLCC
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
MC68HC711E20CFN4
Manufacturer:
FREESCALE
Quantity:
2 100
Part Number:
MC68HC711E20CFN4
Manufacturer:
Freescale Semiconductor
Quantity:
10 000
Chapter 3
Analog-to-Digital (A/D) Converter
3.1 Introduction
The analog-to-digital (A/D) system, a successive approximation converter, uses an all-capacitive charge
redistribution technique to convert analog signals to digital values.
3.2 Overview
The A/D system is an 8-channel, 8-bit, multiplexed-input converter. The converter does not require
external sample and hold circuits because of the type of charge redistribution technique used. A/D
converter timing can be synchronized to the system E clock or to an internal resistor capacitor (RC)
oscillator.
The A/D converter system consists of four functional blocks: multiplexer, analog converter, digital control,
and result storage. Refer to
Figure
3-1.
3.2.1 Multiplexer
The multiplexer selects one of 16 inputs for conversion. Input selection is controlled by the value of bits
CD:CA in the ADCTL register. The eight port E pins are fixed-direction analog inputs to the multiplexer,
and additional internal analog signal lines are routed to it.
Port E pins also can be used as digital inputs. Digital reads of port E pins are not recommended during
the sample portion of an A/D conversion cycle, when the gate signal to the N-channel input gate is on.
Because no P-channel devices are directly connected to either input pins or reference voltage pins,
voltages above V
do not cause a latchup problem, although current should be limited according to
DD
maximum ratings. Refer to
Figure
3-2, which is a functional diagram of an input pin.
3.2.2 Analog Converter
Conversion of an analog input selected by the multiplexer occurs in this block. It contains a
digital-to-analog capacitor (DAC) array, a comparator, and a successive approximation register (SAR).
Each conversion is a sequence of eight comparison operations, beginning with the most significant bit
(MSB). Each comparison determines the value of a bit in the successive approximation register.
The DAC array performs two functions. It acts as a sample and hold circuit during the entire conversion
sequence and provides comparison voltage to the comparator during each successive comparison.
The result of each successive comparison is stored in the SAR. When a conversion sequence is
complete, the contents of the SAR are transferred to the appropriate result register.
A charge pump provides switching voltage to the gates of analog switches in the multiplexer. Charge
pump output must stabilize between 7 and 8 volts within up to 100 µs before the converter can be used.
The charge pump is enabled by the ADPU bit in the OPTION register.
M68HC11E Family Data Sheet, Rev. 5.1
Freescale Semiconductor
57

Related parts for MC68HC711E20CFN4