EE80C196MC Intel, EE80C196MC Datasheet
EE80C196MC
Specifications of EE80C196MC
Available stocks
Related parts for EE80C196MC
EE80C196MC Summary of contents
Page 1
... Information in this document is provided in connection with Intel products Intel assumes no liability whatsoever including infringement of any patent or copyright for sale and use of Intel products except as provided in Intel’s Terms and Conditions of Sale for such products Intel retains the right to make changes to these specifications at any time without notice Microcomputer Products may have minor variations to this specification known as errata ...
Page 2
NOTE Connections between the standard I O ports and the bus are not shown Figure 1 87C196MC Block Diagram 2 270946 – 1 ...
Page 3
... TBD All thermal impedance data is approximate for static air conditions power dissipation Values will change depending on operation conditions and application See the Intel Packaging Handbook (order number 240800) for a description of Intel’s thermal impedance test methodology 8XC196MC Memory Map Description External Memory ...
Page 4
NOTE The pin sequence is correct The 64-Lead SDIP package does not include the following pins P1 4 ACH12 P2 7 COMPARE3 P5 1 INST CLKOUT Figure 2 64-Lead Shrink DIP (SDIP) Package 4 270946 –2 ...
Page 5
NOTE NC means No Connect Do not connect these pins Figure 3 84-Lead PLCC Package 8XC196MC 270946 – ...
Page 6
NOTE NC means No Connect Do not connect these pins Figure 4 80-Lead Shrink EIAJQFP (Quad Flat Pack) 6 270946 – 4 ...
Page 7
... NMI A positive transition on this pin causes a non-maskable interrupt which vectors to memory location 203EH If not used it should be tied used by Intel Evaluation boards PORT0 8-bit high impedance input-only port Also used converter inputs Port0 pins should not be left floating These pins also used to select ...
Page 8
PIN DESCRIPTIONS (Alphabetically Ordered) (Continued) Symbol PORT6 8-bit output port P6 6 and P6 7 output PWM the others are used as the Wave Form Generator outputs Can be used as standard output ports PWM0 PWM1 Programmable duty cycle ...
Page 9
... NOTICE This data sheet contains preliminary infor- mation on new products in production The specifica- tions are subject to change without notice Verify with your local Intel Sales office that you have the latest data sheet before finalizing a design 150 C a WARNING Stressing the device beyond the ‘‘Absolute Maximum Ratings’ ...
Page 10
DC ELECTRICAL CHARACTERISTICS Symbol Parameter I Input Leakage Current on All Input LI Only Pins I Input Leakage Current on Port0 LI1 and Port1 I Input Low Current on BD Ports IL (Note 1) I Input Low Current on ...
Page 11
EXPLANATION OF AC SYMBOLS Each symbol is two pairs of letters prefixed by ‘‘T’’ for time The characters in a pair indicate a signal and its condition respectively Symbols represent the time between the two signal condition points Conditions Signals ...
Page 12
AC ELECTRICAL CHARACTERISTICS Test Conditions Capacitive load on all pins The 87C196MC will meet the following timing specifications Symbol Parameter T XTAL1 to CLKOUT High or Low XHCH T CLKOUT Cycle Time CLCL T CLKOUT High Period CHCL T ...
Page 13
SYSTEM BUS TIMINGS 8XC196MC 270946 – ...
Page 14
READY TIMINGS (One Wait State) BUSWIDTH TIMINGS 14 270946 – 6 270946 – 7 ...
Page 15
EXTERNAL CLOCK DRIVE Symbol Parameter 1 T Oscillator Frequency XLXL T Oscillator Period XLXL T High Time XHXX T Low Time XLXX T Rise Time XLXH T Fall Time XHXL EXTERNAL CRYSTAL CONNECTIONS NOTE Keep oscillator components close to chip ...
Page 16
CHARACTERISTICS The sample and conversion time of the A D convert the 8-bit or 10-bit modes is programmed by loading a byte into the AD TIME Special Function Register This allows optimizing the A ...
Page 17
MODE A D OPERATING CONDITIONS Symbol Description T Ambient Temperature A V Digital Supply Voltage CC V Analog Supply Voltage REF T Sample Time SAM T Conversion Time CONV F Oscillator Frequency OSC NOTES ANGND and V should nominally ...
Page 18
MODE A D OPERATING CONDITIONS Symbol Description T Ambient Temperature A V Digital Supply Voltage CC V Analog Supply Voltage REF T Sample Time SAM T Conversion Time CONV F Oscillator Frequency OSC NOTES ANGND and V should ...
Page 19
EPROM SPECIFICATIONS OPERATING CONDITIONS Symbol Description T Ambient Temperature during Programming A V Supply Voltage during Programming CC V Reference Supply Voltage during Programming REF V Programming Voltage Pin Voltage EA F Oscillator Frequency during Auto OSC ...
Page 20
DC EPROM PROGRAMMING CHARACTERISTICS Symbol Parameter I V Supply Current (When Programming NOTE Do not apply V until V is stable and within specifications and the oscillator clock has stabilized or the device may ...
Page 21
SLAVE PROGRAMMING MODE IN WORD DUMP WITH AUTO INCREMENT NOTE P3 0 must be low (‘‘0’’) SLAVE PROGRAMMING MODE TIMING IN DATA PROGRAM WITH REPEATED PROG PULSE AND AUTO INCREMENT 8XC196MC 270946 –12 270946 –13 21 ...
Page 22
... This data sheet (270946-004) is valid for devices with a ‘‘B’’ at the end of the topside tracking number Data sheets are changed as new device information becomes available Verify with your local Intel sales office that you have the latest version before finaliz- ing a design or ordering devices ...