EE80C196MD Intel, EE80C196MD Datasheet
EE80C196MD
Specifications of EE80C196MD
Available stocks
Related parts for EE80C196MD
EE80C196MD Summary of contents
Page 1
... Information in this document is provided in connection with Intel products Intel assumes no liability whatsoever including infringement of any patent or copyright for sale and use of Intel products except as provided in Intel’s Terms and Conditions of Sale for such products Intel retains the right to make changes to these specifications at any time without notice Microcomputer Products may have minor variations to this specification known as errata ...
Page 2
NOTE Connections between the standard I O ports and the bus are not shown Figure 1 87C196MD Block Diagram 2 272323 – 1 ...
Page 3
... C W All thermal impedance data is approximate for static air conditions power dissipation Values will change depending on operation conditions and application See the Intel Packaging Handbook (order number 240800) for a description of Intel’s thermal impedance test methodology Table 2 8XC196MD Memory Map Description External Memory ...
Page 4
AND 8XC196MD DIFFERENCES INT MASK1 INT PEND1 Registers There are some differences between 8XC196MC and 8XC196MD INT MASK1 INT PEND1 registers The 8XC196MD interrupt mask and pending registers are shown below No- tice that the CAPCOM5 COMP4 and ...
Page 5
Table 3 Interrupt Sources Vectors and Priorities Interrupt Source Symbol Capture Compare5 CAPCOMP5 Compare4 COMP4 Capture Compare4 CAPCOMP4 Interrupt and PTS Vectors The 8XC196MD has three new interrupt and PTS vectors which are Capture Compare5 Compare 4 and Capture Compare4 ...
Page 6
Port 1 There are three additional Port 1 input pins (P1 5 – that were not available on the 8XC196MC These pins are listed below followed by their func- tion Table 6 New 8XC196MD Port 1 Pins ...
Page 7
NOTE NC means No Connect Do not connect these pins Figure 6 84-Lead PLCC Package 8XC196MD 272323 – ...
Page 8
Figure 7 80-Lead Shrink EIAJQFP (Quad Flat Pack) 8 272323 – 4 ...
Page 9
... NMI A positive transition on this pin causes a non-maskable interrupt which vectors to memory location 203EH If not used it should be tied used by Intel Evaluation boards PORT0 8-bit high impedance input-only port Also used converter inputs Port0 pins should not be left floating These pins also used to select ...
Page 10
PIN DESCRIPTIONS (Alphabetically Ordered) (Continued) Symbol PORT2 8-bit bidirectional I O port All of the Port2 pins are shared with the EPA I O pins (CAPCOMP0 – 3 and COMPARE0 – 3) PORT3 8-bit bidirectional I O ports with ...
Page 11
PIN DESCRIPTIONS (Alphabetically Ordered) (Continued) Symbol PALE A falling edge in Slave Programming Mode and Auto Configuration Byte Programming Mode indicates that ports 3 and 4 contain valid programming (P2 1) address command information (input to slave) PROG A falling ...
Page 12
... NOTICE This data sheet contains preliminary infor- mation on new products in production The specifica- tions are subject to change without notice Verify with your local Intel Sales office that you have the latest data sheet before finalizing a design 150 C a WARNING Stressing the device beyond the ‘‘Absolute Maximum Ratings’ ...
Page 13
DC ELECTRICAL CHARACTERISTICS Symbol Parameter I Input Leakage Current on All Input LI Only Pins I Input Leakage Current on Port0 LI1 and Port1 I Input Low Current on BD Ports IL (Note 1) I Input Low Current on P5 ...
Page 14
EXPLANATION OF AC SYMBOLS Each symbol is two pairs of letters prefixed by ‘‘T’’ for time The characters in a pair indicate a signal and its condition respectively Symbols represent the time between the two signal condition points Conditions ...
Page 15
AC ELECTRICAL CHARACTERISTICS Test Conditions Capacitive load on all pins The 87C196MD will meet the following timing specifications Symbol Parameter T XTAL1 to CLKOUT High or Low XHCH T CLKOUT Cycle Time CLCL T CLKOUT High Period CHCL T CLKOUT ...
Page 16
SYSTEM BUS TIMINGS 16 272323 – 5 ...
Page 17
READY TIMINGS (One Wait State) BUSWIDTH TIMINGS 8XC196MD 272323 – 6 272323 – ...
Page 18
EXTERNAL CLOCK DRIVE Symbol Parameter 1 T Oscillator Frequency XLXL T Oscillator Period XLXL T High Time XHXX T Low Time XLXX T Rise Time XLXH T Fall Time XHXL EXTERNAL CRYSTAL CONNECTIONS NOTE Keep oscillator components close to ...
Page 19
CHARACTERISTICS The sample and conversion time of the A D convert the 8-bit or 10-bit modes is programmed by loading a byte into the AD TIME Special Function Register This allows optimizing the A D ...
Page 20
MODE A D OPERATING CONDITIONS Symbol Description T Ambient Temperature A V Digital Supply Voltage CC V Analog Supply Voltage REF T Sample Time SAM T Conversion Time CONV F Oscillator Frequency OSC NOTES ANGND and V should ...
Page 21
MODE A D OPERATING CONDITIONS Symbol Description T Ambient Temperature A V Digital Supply Voltage CC V Analog Supply Voltage REF T Sample Time SAM T Conversion Time CONV F Oscillator Frequency OSC NOTES ANGND and V should nominally ...
Page 22
EPROM SPECIFICATIONS OPERATING CONDITIONS DURING PROGRAMMING Symbol Description T Ambient Temperature during Programming A V Supply Voltage during Programming CC V Reference Supply Voltage during Programming REF V Programming Voltage Pin Voltage EA F Oscillator Frequency ...
Page 23
DC EPROM PROGRAMMING CHARACTERISTICS Symbol Parameter I V Supply Current (When Programming NOTE Do not apply V until V is stable and within specifications and the oscillator clock has stabilized or the device may damaged ...
Page 24
SLAVE PROGRAMMING MODE IN WORD DUMP WITH AUTO INCREMENT NOTE P3 0 must be low (‘‘0’’) SLAVE PROGRAMMING MODE TIMING IN DATA PROGRAM WITH REPEATED PROG PULSE AND AUTO INCREMENT 24 272323 –14 272323 –15 ...
Page 25
... Data sheets are changed as new device information becomes available Verify with your local Intel sales office that you have the latest version before finalizing a design or ordering devic- es 8XC196MD ...