LM224N STMicroelectronics, LM224N Datasheet - Page 3

IC OP AMP LP QUAD 14-DIP

LM224N

Manufacturer Part Number
LM224N
Description
IC OP AMP LP QUAD 14-DIP
Manufacturer
STMicroelectronics
Datasheets

Specifications of LM224N

Amplifier Type
General Purpose
Number Of Circuits
4
Slew Rate
0.4 V/µs
Gain Bandwidth Product
1.3MHz
Current - Input Bias
20nA
Voltage - Input Offset
2000µV
Current - Supply
1.5mA
Current - Output / Channel
70mA
Voltage - Supply, Single/dual (±)
3 V ~ 30 V, ±1.5 V ~ 15 V
Operating Temperature
-40°C ~ 105°C
Mounting Type
Through Hole
Package / Case
14-DIP (0.300", 7.62mm)
Number Of Channels
4
Common Mode Rejection Ratio (min)
70 dB
Input Offset Voltage
5 mV
Input Bias Current (max)
150 nA
Operating Supply Voltage
5 V, 9 V, 12 V, 15 V
Supply Current
1.2 mA
Maximum Power Dissipation
500 mW
Maximum Operating Temperature
+ 105 C
Minimum Operating Temperature
- 40 C
Dual Supply Voltage
+/- 3 V, +/- 5 V, +/- 9 V, +/- 12 V
Maximum Dual Supply Voltage
+/- 15 V
Minimum Dual Supply Voltage
+/- 1.5 V
Mounting Style
Through Hole
Shutdown
No
Supply Voltage (max)
30 V
Supply Voltage (min)
3 V
Technology
Bipolar
Voltage Gain Db
100 dB
Bandwidth
1.3 MHz
Channel Separation
120
Common Mode Rejection Ratio
80
Current, Input Bias
20 nA
Current, Input Offset
2 nA
Current, Output
40 mA
Current, Supply
1.5 mA
Harmonic Distortion
0.015 %
Number Of Amplifiers
Quad
Package Type
DIP-14
Power Dissipation
500 mW
Signal Gain
100 V/mV
Temperature, Operating, Range
-40 to +105 °C
Voltage, Input
32 V
Voltage, Noise
40 nV/sqrt Hz
Voltage, Offset
2 mV
Voltage, Output, High
28 V
Voltage, Output, Low
5 mV
Voltage, Supply
3 to 30 V
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Output Type
-
-3db Bandwidth
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
497-1547-5

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
LM224N
Manufacturer:
TI
Quantity:
30 000
Part Number:
LM224N
Manufacturer:
ON
Quantity:
2
Part Number:
LM224N
Manufacturer:
ST
Quantity:
10
Part Number:
LM224N
Manufacturer:
PHI
Quantity:
1 000
Part Number:
LM224N
Manufacturer:
ST
0
Part Number:
LM224N
Manufacturer:
ST
Quantity:
20 000
Part Number:
LM224N
Manufacturer:
TI
Quantity:
16 984
Part Number:
LM224N
0
Part Number:
LM224N ST
Manufacturer:
ST
0
Part Number:
LM224N(S
Manufacturer:
ST
0
Part Number:
LM224NG
Manufacturer:
ON Semiconductor
Quantity:
65
LM124, LM224, LM324
2
Table 1.
1. Either or both input voltages must not exceed the magnitude of V
2. Differential voltages are the non-inverting input terminal with respect to the inverting input terminal.
3. Short-circuits from the output to V
4. This input current only exists when the voltage at any of the input leads is driven negative. It is due to the collector-base
5. The junction base/substrate of the input PNP transistor polarized in reverse must be protected by a resistor in series with
6. Short-circuits can cause excessive heating. Destructive dissipation can result from simultaneous short-circuits on all
7. Human body model, 100 pF discharged through a 1.5 kΩ resistor into pin of device.
8. Machine model ESD: a 200 pF capacitor is charged to the specified voltage, then discharged directly into the IC with no
9. Charged device model: all pins plus package are charged together to the specified voltage and then discharged directly to
Symbol
T
R
R
ESD
V
T
V
V
are with respect to ground terminal.
approximately 40 mA independent of the magnitude of V
circuits on all amplifiers.
junction of the input PNP transistor becoming forward-biased and thereby acting as input diode clamp. In addition to this
diode action, there is NPN parasitic action on the IC chip. This transistor action can cause the output voltages of the op-
amps to go to the V
This is not destructive and normal output is restored for input voltages above -0.3 V.
the inputs to limit the input current to 400 µA max (R = (Vin - 32 V)/400 µA).
amplifiers. These are typical values given for a single layer board (except for TSSOP, a two-layer board).
external series resistor (internal resistor < 5 Ω), into pin-to-pin of device.
ground.
oper
I
T
thja
CC
stg
thjc
in
in
id
j
Supply voltage
Input voltage
Differential input voltage
Output short-circuit duration
Input current
Input current
AMR value
Operating free-air temperature range
Storage temperature range
Maximum junction temperature
Thermal resistance junction to ambient
SO14
TSSOP14
DIP14
Thermal resistance junction to case
SO14
TSSOP14
DIP14
HBM: human body model
MM: machine model
CDM: charged device model
Absolute maximum ratings
Absolute maximum ratings
CC
(1)
(5)
voltage level (or to ground for a large overdrive) for the time during which an input is driven negative.
(4)
Parameter
: V
: V
in
in
driven positive above
driven negative
(8)
CC
(2)
(7)
can cause excessive heating if V
(9)
(3)
Doc ID 2156 Rev 6
(6)
5 mA in DC or 50 mA in AC (duty cycle = 10%, T=1s)
0.4
CC
. Destructive dissipation can result from simultaneous short-
-55 to +125
LM124
CC
+
or V
CC
CC
> 15 V. The maximum output current is
-
. All voltage values, except differential voltages
-65 to +150
±16 or 32
-0.3 to 32
Infinite
-40 to +105
1500
150
103
100
250
150
32
83
31
32
33
LM224
Absolute maximum ratings
0 to +70
LM324
°C/W
°C/W
Unit
mA
°C
°C
°C
V
V
V
V
3/19

Related parts for LM224N