LMV822MX/NOPB National Semiconductor, LMV822MX/NOPB Datasheet - Page 12

• Manufacturer Part Number: LMV822MX/NOPB
• Description: IC OP AMP R-R LOW VOLT LP 8-SOIC
• Manufacturer: National Semiconductor

Specifications of LMV822MX/NOPB

• Amplifier Type: General Purpose
• Number Of Circuits: 2
• Output Type: Rail-to-Rail
• Slew Rate: 2 V/µs
• Gain Bandwidth Product: 5.6MHz
• Current - Input Bias: 100nA
• Voltage - Input Offset: 3500µV
• Current - Supply: 500µA
• Current - Output / Channel: 45mA
• Voltage - Supply, Single/dual (±): 2.5 V ~ 5.5 V, ±1.25 V ~ 2.75 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 8-SOIC (3.9mm Width)
• Rail/rail I/o Type: Rail to Rail Output
• Number Of Elements: 2
• Unity Gain Bandwidth Product: 5.6MHz
• Common Mode Rejection Ratio: 72dB
• Input Offset Voltage: 3.5@5VmV
• Input Bias Current: 100nA
• Single Supply Voltage (typ): 2.7/5V
• Dual Supply Voltage (typ): Not RequiredV
• Voltage Gain In Db: 105dB
• Power Supply Rejection Ratio: 75dB
• Power Supply Requirement: Single
• Shut Down Feature: No
• Single Supply Voltage (min): 2.5V
• Single Supply Voltage (max): 5.5V
• Dual Supply Voltage (min): Not RequiredV
• Dual Supply Voltage (max): Not RequiredV
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 8
• Package Type: SOIC N
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• -3db Bandwidth: -
• Lead Free Status / Rohs Status: Compliant
• Other names: LMV822MX; LMV822MXTR

www.national.com
Application Note
UNITY GAIN PULSE RESPONSE CONSIDERATION
A pull-up resistor is well suited for increasing unity-gain,
pulse response stability. For example, a 600 Ω pull-up resis-
tor reduces the overshoot voltage by about 50%, when
driving a 220 pF load. Figure 3 shows how to implement the
pull-up resistor for more pulse response stability.
Higher capacitances can be driven by decreasing the value
of the pull-up resistor, but its value shouldn’t be reduced
beyond the sinking capability of the part. An alternate ap-
proach is to use an isolation resistor as illustrated in Figure 4
.
Figure 5 shows the resulting pulse response from a LMV824,
while driving a 10,000 pF load through a 20Ω isolation
resistor.
FIGURE 4. Using an Isolation Resistor to Drive Heavy
FIGURE 3. Using a Pull-up Resistor at the Output for
FIGURE 2. Unity-Gain Frequency vs Common Mode
Stabilizing Capacitive Loads
Voltage for Various Loads
Capacitive Loads
(Continued)
10012841
10012861
10012843
12
INPUT BIAS CURRENT CONSIDERATION
Input bias current (I
offset voltage. This offset is primarily due to I
through the negative feedback resistor, R
is 90 nA (max
mV will be developed (V
resistor (R
But the input offset current (I
offset voltage in the same manner - typically 0.05 mV at
room temp.
APPLICATION CIRCUITS
This section covers the following application circuits:
1. Telephone-Line Transceiver
2. “Simple” Mixer (Amplitude Modulator)
FIGURE 6. Canceling the Voltage Offset Effect of Input
FIGURE 5. Pulse Response per Figure 4
C
), as shown in Figure 6, cancels out this affect.
@
room) and R
B
) can develop a somewhat significant
Bias Current
OS
=I
F
B
OS
is 100 kΩ, then an offset of 9
x R
) will still contribute to an
F
).Using a compensation
F
. For example, if I
10012854
10012859
B
flowing
B