LMV822MX/NOPB National Semiconductor, LMV822MX/NOPB Datasheet - Page 13

• Manufacturer Part Number: LMV822MX/NOPB
• Description: IC OP AMP R-R LOW VOLT LP 8-SOIC
• Manufacturer: National Semiconductor

Specifications of LMV822MX/NOPB

• Amplifier Type: General Purpose
• Number Of Circuits: 2
• Output Type: Rail-to-Rail
• Slew Rate: 2 V/µs
• Gain Bandwidth Product: 5.6MHz
• Current - Input Bias: 100nA
• Voltage - Input Offset: 3500µV
• Current - Supply: 500µA
• Current - Output / Channel: 45mA
• Voltage - Supply, Single/dual (±): 2.5 V ~ 5.5 V, ±1.25 V ~ 2.75 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 8-SOIC (3.9mm Width)
• Rail/rail I/o Type: Rail to Rail Output
• Number Of Elements: 2
• Unity Gain Bandwidth Product: 5.6MHz
• Common Mode Rejection Ratio: 72dB
• Input Offset Voltage: 3.5@5VmV
• Input Bias Current: 100nA
• Single Supply Voltage (typ): 2.7/5V
• Dual Supply Voltage (typ): Not RequiredV
• Voltage Gain In Db: 105dB
• Power Supply Rejection Ratio: 75dB
• Power Supply Requirement: Single
• Shut Down Feature: No
• Single Supply Voltage (min): 2.5V
• Single Supply Voltage (max): 5.5V
• Dual Supply Voltage (min): Not RequiredV
• Dual Supply Voltage (max): Not RequiredV
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 8
• Package Type: SOIC N
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• -3db Bandwidth: -
• Lead Free Status / Rohs Status: Compliant
• Other names: LMV822MX; LMV822MXTR

Application Note
3. Dual Amplifier Active Filters (DAAFs)
4. Tri-level Voltage Detector
TELEPHONE-LINE TRANSCEIVER
The telephone-line transceiver of Figure 7 provides a full-
duplexed connection through a PCMCIA, miniature trans-
former. The differential configuration of receiver portion
(UR), cancels reception from the transmitter portion (UT).
Note that the input signals for the differential configuration of
UR, are the transmit voltage (V
R
ance; therefore dividing V
R
chosen to cancel the V
following equation:
Note that Cr is included for canceling out the inadequacies of
the lossy, miniature transformer. Refer to application note
AN-397 for detailed explanation.
“SIMPLE” MIXER (AMPLITUDE MODULATOR)
The mixer of Figure 8 is simple and provides a unique form
of amplitude modulation. Vi is the modulation frequency
(F
carrier frequency (F
inverting and non-inverting unity gain configurations. Offset-
ting a sine wave above ground at Vi results in the oscillo-
scope photo of Figure 9.
The simple mixer can be applied to applications that utilize
the Doppler Effect to measure the velocity of an object. The
difference frequency is one of its output frequency compo-
nents. This difference frequency magnitude (/F
key factor for determining an object’s velocity per the Dop-
pler Effect. If a signal is transmitted to a moving object, the
reflected frequency will be a different frequency. This differ-
ence in transmit and receive frequency is directly propor-
tional to an object’s velocity.
•
•
match
match
FIGURE 7. Telephone-line Transceiver for a PCMCIA
M
), while a +3V square-wave at the gate of Q1, induces a
a. Low-Pass Filter (LPF)
b. High-Pass Filter (HPF)
). The differential configuration of UR has its resistors
is chosen to match the coupled telephone-line imped-
C
). Q1 switches (toggles) U1 between
Modem Card
T
and V
T
(Continued)
by two (assuming R1
T
) and V
T
/2 inputs according to the
T
/2. This is because
M
-F
C
10012833
/) is the
>>
13
DUAL AMPLIFIER ACTIVE FILTERS (DAAFs)
The LMV822/24 bring economy and performance to DAAFs.
The low-pass and the high-pass filters of Figure 10 and
Figure 11 (respectively), offer one key feature: excellent
sensitivity performance. Good sensitivity is when deviations
in component values cause relatively small deviations in a
filter’s parameter such as cutoff frequency (Fc). Single am-
plifier active filters like the Sallen-Key provide relatively poor
sensitivity performance that sometimes cause problems for
high production runs; their parameters are much more likely
to deviate out of specification than a DAAF would. The
DAAFs of Figure 10 and Figure 11 are well suited for high
volume production.
FIGURE 9. Output signal per the Circuit of Figure 8
FIGURE 8. Amplitude Modulator Circuit
www.national.com
10012840
f
f
10012839
mod
carrier