LM258PT STMicroelectronics, LM258PT Datasheet - Page 6

• Manufacturer Part Number: LM258PT
• Description: IC OP AMP DUAL LOW POWER 8-TSSOP
• Manufacturer: STMicroelectronics

Specifications of LM258PT

• Amplifier Type: General Purpose
• Number Of Circuits: 2
• Slew Rate: 0.6 V/µs
• Gain Bandwidth Product: 1.1MHz
• Current - Input Bias: 20nA
• Voltage - Input Offset: 2000µV
• Current - Supply: 700µA
• Current - Output / Channel: 60mA
• Voltage - Supply, Single/dual (±): 3 V ~ 30 V, ±1.5 V ~ 15 V
• Operating Temperature: -40°C ~ 105°C
• Mounting Type: Surface Mount
• Package / Case: 8-TSSOP
• Number Of Channels: 2
• Voltage Gain Db: 100 dB
• Common Mode Rejection Ratio (min): 70 dB
• Input Offset Voltage: 5 mV
• Operating Supply Voltage: 5 V, 9 V, 12 V, 15 V
• Supply Current: 1.2 mA
• Maximum Power Dissipation: 500 mW
• Maximum Operating Temperature: + 105 C
• Mounting Style: SMD/SMT
• Maximum Dual Supply Voltage: +/- 15 V
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Output Type: -
• -3db Bandwidth: -
• Lead Free Status / Rohs Status: In Transition
• Other names: 497-7815-2; LM258PT

Electrical characteristics
Table 3.
1. V
2. The direction of the input current is out of the IC. This current is essentially constant, independent of the state of the output
3. The input common-mode voltage of either input signal voltage should not be allowed to go negative by more than 0.3 V.
4. Due to the proximity of external components, ensure that stray capacitance between these external parts does not cause
6/19
Symbol
V
I
so there is no change in the load on the input lines.
The upper end of the common-mode voltage range is V
damage.
coupling. Typically, this can be detected because this type of capacitance increases at higher frequencies.
CMR
source
GBP
THD
o1
V
I
V
SR
o
sink
e
OH
OL
/V
= 1.4 V, R
n
o2
Common mode rejection ratio
R
T
Output current source
V
Output sink current
High level output voltage
R
R
Low level output voltage
R
T
Slew rate
Gain bandwidth product
V
R
Total harmonic distortion
f = 1 kHz, A
C
Equivalent input noise voltage
f = 1 kHz, R
Channel separation
1 kHz ≤ f ≤ 20 kHz
Electrical characteristics for V
(unless otherwise specified) (continued)
min
min
CC
CC
s
L
L
L
L
L
s
V
V
T
T
V
C
= 0 Ω, 5 V < V
≤ 10 kΩ
= 2 kΩ, V
= 10 kΩ, V
= 10 kΩ
= 2 kΩ , C
= 100 pF, V
min
min
CC
CC
CC
L
+
+
≤ T
≤ T
= 100 pF, unity gain
= +15 V, V
= 30 V, f = 100 kHz, V
+
+
+
≤ T
≤ T
amb
= +15 V, V
= +15 V, V
amb
= 15 V, V
amb
amb
v
s
L
≤ T
≤ T
CC
= 20 dB, R
= 100 Ω, V
= 100 pF
CC
≤ T
≤ T
O
max
CC
+
max
o
i
= 2 V
+
= 30 V
= +2 V, V
max
+
max
= 0.5 to 3 V, R
o
o
= 30 V
< 30 V, 0 < V
(4)
Parameter
= +2 V, V
= +0.2 V, V
pp
L
CC
= 2 kΩ, V
id
+
in
= +1 V
= 30 V
id
= 10 mV,
id
= -1 V
ic
L
= -1 V
< V
= 2 kΩ ,
o
CC
CC
= 2 V
+
CC
+
- 1.5 V
= +5 V, V
+
pp
- 1.5 V, but either or both inputs can go to +32 V without
,
CC
-
Min.
= Ground, V
0.3
0.7
70
60
20
10
12
26
26
27
27
Typ.
0.02
120
0.6
1.1
85
40
20
50
27
28
55
o
5
= 1.4 V, T
LM158-LM258-LM358
Max.
60
20
20
amb
= +25°C
MHz
Unit
V/µs
----------- -
mA
mA
mV
dB
µA
dB
nV
%
V
Hz