IC OPAMP GP R-R 6.4MHZ 8MSOP

TLV2462IDGKR

Manufacturer Part NumberTLV2462IDGKR
DescriptionIC OPAMP GP R-R 6.4MHZ 8MSOP
ManufacturerTexas Instruments
TLV2462IDGKR datasheets
 


Specifications of TLV2462IDGKR

Amplifier TypeGeneral PurposeNumber Of Circuits2
Output TypeRail-to-RailSlew Rate1.6 V/µs
Gain Bandwidth Product6.4MHzCurrent - Input Bias1.3nA
Voltage - Input Offset500µVCurrent - Supply550µA
Current - Output / Channel80mAVoltage - Supply, Single/dual (±)2.7 V ~ 6 V, ±1.35 V ~ 3 V
Operating Temperature-40°C ~ 125°CMounting TypeSurface Mount
Package / Case8-MSOP, Micro8™, 8-uMAX, 8-uSOP,Number Of Channels2
Common Mode Rejection Ratio (min)71 dBInput Voltage Range (max)Positive Rail
Input Voltage Range (min)Negative RailInput Offset Voltage2 mV
Input Bias Current (max)14 nAOutput Current (typ)80 mA
Operating Supply Voltage6 VSupply Current1.3 mA
Maximum Power Dissipation481 mWMaximum Operating Temperature+ 125 C
Minimum Operating Temperature- 40 CDual Supply Voltage+/- 3 V
Maximum Dual Supply Voltage+/- 3 VMinimum Dual Supply Voltage+/- 1.35 V
Mounting StyleSMD/SMTShutdownNo
Supply Voltage (max)6 VSupply Voltage (min)2.7 V
Voltage Gain Db109 dBLead Free Status / RoHS StatusLead free / RoHS Compliant
-3db Bandwidth-Other names296-7561-2
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
Page 21
22
Page 22
23
Page 23
24
Page 24
25
Page 25
26
Page 26
27
Page 27
28
Page 28
29
Page 29
30
Page 30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
Page 27/72

Download datasheet (3Mb)Embed
PrevNext
shutdown function
Three members of the TLV246x family (TLV2460/3/5) have a shutdown terminal for conserving battery life in
portable applications. When the shutdown terminal is tied low, the supply current is reduced to 0.3 A/channel,
the amplifier is disabled, and the outputs are placed in a high impedance mode. To enable the amplifier, the
shutdown terminal can either be left floating or pulled high. When the shutdown terminal is left floating, care
should be taken to ensure that parasitic leakage current at the shutdown terminal does not inadvertently place
the operational amplifier into shutdown. The shutdown terminal threshold is always referenced to V
Therefore, when operating the device with split supply voltages (e.g. 2.5 V), the shutdown terminal needs to
be pulled to V
− (not GND) to disable the operational amplifier.
DD
The amplifier’s output with a shutdown pulse is shown in Figures 22, 23, 24, and 25. The amplifier is powered
with a single 5-V supply and configured as a noninverting configuration with a gain of 5. The amplifier turnon
and turnoff times are measured from the 50% point of the shutdown pulse to the 50% point of the output
waveform. The times for the single, dual, and quad are listed in the data tables.
circuit layout considerations
To achieve the levels of high performance of the TLV246x, follow proper printed-circuit board design techniques.
A general set of guidelines is given in the following.
D
Ground planes − It is highly recommended that a ground plane be used on the board to provide all
components with a low inductive ground connection. However, in the areas of the amplifier inputs and
output, the ground plane can be removed to minimize the stray capacitance.
D
Proper power supply decoupling − Use a 6.8- F tantalum capacitor in parallel with a 0.1- F ceramic
capacitor on each supply terminal. It may be possible to share the tantalum among several amplifiers
depending on the application, but a 0.1- F ceramic capacitor should always be used on the supply terminal
of every amplifier. In addition, the 0.1- F capacitor should be placed as close as possible to the supply
terminal. As this distance increases, the inductance in the connecting trace makes the capacitor less
effective. The designer should strive for distances of less than 0.1 inches between the device power
terminals and the ceramic capacitors.
D
Sockets − Sockets can be used but are not recommended. The additional lead inductance in the socket pins
will often lead to stability problems. Surface-mount packages soldered directly to the printed-circuit board
is the best implementation.
D
Short trace runs/compact part placements − Optimum high performance is achieved when stray series
inductance has been minimized. To realize this, the circuit layout should be made as compact as possible,
thereby minimizing the length of all trace runs. Particular attention should be paid to the inverting input of
the amplifier. Its length should be kept as short as possible. This will help to minimize stray capacitance at
the input of the amplifier.
D
Surface-mount passive components − Using surface-mount passive components is recommended for high
performance amplifier circuits for several reasons. First, because of the extremely low lead inductance of
surface-mount components, the problem with stray series inductance is greatly reduced. Second, the small
size of surface-mount components naturally leads to a more compact layout thereby minimizing both stray
inductance and capacitance. If leaded components are used, it is recommended that the lead lengths be
kept as short as possible.
SLOS220J − JULY 1998 − REVISED FEBRUARY 2004
APPLICATION INFORMATION
WWW.TI.COM
/2.
DD
27