LT1006S8 Linear Technology, LT1006S8 Datasheet
LT1006S8
Specifications of LT1006S8
Available stocks
Related parts for LT1006S8
LT1006S8 Summary of contents
Page 1
... Pin 8. For similar single supply precision dual and quad op amps, please see the LT1013/LT1014 data sheet. For micropower dual and quad op amps, please see the LT1078/LT1079 data sheet. , LTC and LT are registered trademarks of Linear Technology Corporation. 360k 1/4 CD4066 390Ω – ...
Page 2
... Input Noise Current Density n Input Resistance Differential Mode Common Mode 2 U (Note 1) Operating Temperature Range LT1006AM/LT1006M (OBSOLETE)....– 55°C to 125°C LT1006AC/LT1006C/LT1006S8 ............... 0°C to 70°C Storage Temperature Range ................. – 65°C to 150°C Lead Temperature (Soldering, 10 sec).................. 300° ORDER PART NUMBER TRIM – ...
Page 3
ELECTRICAL CHARACTERISTICS SYMBOL PARAMETER Input Voltage Range CMRR Common Mode Rejection Ratio PSRR Power Supply Rejection Ratio A Large-Signal Voltage Gain VOL Maximum Output Voltage Swing SR Slew Rate I Supply Current S Minimum Supply Voltage The denotes the specifications ...
Page 4
... N8 Package S8 Package J8/H Package N8 Package S8 Package V = 0.04V to 3. ±2V to ±18V 101 S O Output Low, 600Ω to GND Output High, 600Ω to GND 3.3 LT1006AM/AC CONDITIONS MIN LT1006S8 13.5 –15 +13.5V, –15V 100 ±2V to ±18V 106 ±10V 1 ±10V 600Ω 0 ±13 ...
Page 5
ELECTRICAL CHARACTERISTICS temperature range ±15V, –55°C ≤ SYMBOL PARAMETER V Input Offset Voltage OS ∆V Input Offset Voltage Drift OS ∆Temp I Input Offset Current OS I Input Bias Current B A Large-Signal Voltage Gain VOL ...
Page 6
LT1006 W U TYPICAL PERFOR A CE CHARACTERISTICS Offset Voltage Drift with Temperature of Representative Units 150 120 –30 –60 –90 –120 –150 – ...
Page 7
W U TYPICAL PERFOR A CE CHARACTERISTICS 10Hz Voltage Noise Distribution 100 V = ±2. 25°C A 200 UNITS TESTED 80 FROM THREE RUNS VOLTAGE NOISE DENSITY (nV/√Hz) ...
Page 8
LT1006 W U TYPICAL PERFOR A CE CHARACTERISTICS Voltage Gain vs Frequency 140 T = 25° 10pF 120 L 100 5V ±15V –20 0.01 0.1 ...
Page 9
U U APPLICATIO S I FOR ATIO The LT1006 is fully specified for single supply operation, (i.e., when the negative supply is 0V). Input common mode range includes ground; the output swings within a few millivolts of ground. Single supply ...
Page 10
LT1006 U U APPLICATIO S I FOR ATIO In automated production testing the output is forced to 1.4V by the test loop; offset voltage is measured with a common mode voltage of zero and the negative supply at zero (Pin ...
Page 11
U TYPICAL APPLICATIO S Platinum RTD Signal Conditioner with Curvature Correction + 5.6V TO 10V 39k 1µF LM334 1.21k* 5k 400°C TRIM I = 100µA 43.2k** 12k* 1N457 K +V 10k* 50k 180k 1k** 1k** 5°C 7 TRIM ...
Page 12
LT1006 U TYPICAL APPLICATIO S Micropower Thermocouple Signal Conditioner with Cold Junction Compensation 100k CATALYST RESEARCH CORP MODEL 2736 2.8V TYPE J THERMOCOUPLE 5V 10k 5% 1k 0°C 16.2k LT1004 1.235V 3.2k T1 6250Ω 12 4.5V (3AA CELLS) R4 233k* ...
Page 13
U TYPICAL APPLICATIO S DIFFERENTIAL INPUT 0.01 F – SCHE ATIC DIAGRA + 1.6k Q5 Q13 Q6 Q27 +IN Q22 Q21 400Ω –IN 2 400Ω Q12 Q11 Q9 75pF – V ...
Page 14
LT1006 PACKAGE DESCRIPTIO .045 – .068 (1.143 – 1.650) FULL LEAD OPTION .300 BSC (7.62 BSC) .008 – .018 (0.203 – 0.457) NOTE: LEAD DIMENSIONS APPLY TO SOLDER DIP/PLATE OR TIN PLATE LEADS Package 8-Lead TO-5 Metal ...
Page 15
... MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED .010 INCH (0.254mm) Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no represen- tation that the interconnection of its circuits as described herein will not infringe on existing patent rights. ...
Page 16
... INCHES (MILLIMETERS) www.linear.com .189 – .197 (4.801 – 5.004) NOTE .150 – .157 (3.810 – 3.988) NOTE 3 N .004 – .010 (0.101 – 0.254) .050 (1.270) BSC SO8 0502 LT/TP 1102 1K REV A • PRINTED IN USA LINEAR TECHNOLOGY CORPORATION 1988 1006fa ...