IC OPAMP CFB 1.7GHZ SGL SOT23-6

 

OPA695IDBVRG4

Manufacturer Part NumberOPA695IDBVRG4
DescriptionIC OPAMP CFB 1.7GHZ SGL SOT23-6
ManufacturerTexas Instruments
OPA695IDBVRG4 datasheets

Availability: In stock

International delivery:

Warranty: 60 days

Shipping & payment terms

Added to cart

Select quantity

 

Specifications of OPA695IDBVRG4

Amplifier TypeCurrent FeedbackNumber Of Circuits1
Slew Rate4300 V/µs-3db Bandwidth1.7GHz
Current - Input Bias20µAVoltage - Input Offset300µV
Current - Supply12.9mACurrent - Output / Channel120mA
Voltage - Supply, Single/dual (±)5 V ~ 12 V, ±2.5 V ~ 6 VOperating Temperature-40°C ~ 85°C
Mounting TypeSurface MountPackage / CaseSOT-23-6
Number Of Channels1Common Mode Rejection Ratio (min)51 dB
Input Offset Voltage3 mVOperating Supply Voltage12 V
Supply Current13.3 mAMaximum Operating Temperature+ 85 C
Mounting StyleSMD/SMTMaximum Dual Supply Voltage+/- 6 V
Minimum Operating Temperature- 40 CFor Use WithTSW3070EVM - TSW3070EVM296-19683 - BOARD DEMO FOR SNGL SOT23 OPAMPS
Lead Free Status / RoHS StatusLead free / RoHS CompliantOutput Type-
Gain Bandwidth Product-  
1
2
3
4
5
6
7
8
9
10
11
Page 11
12
Page 12
13
Page 13
14
Page 14
15
Page 15
16
Page 16
17
Page 17
18
Page 18
19
Page 19
20
Page 20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
Page 16/39

Download datasheet (2Mb)Embed
PrevNext
curves. The inverting configuration holds almost constant
bandwidth (with correctly selected external resistor values)
until R
reduces to equal 50 , and remains at that value to
G
satisfy the input impedance matching requirement, with fur-
ther increases in gain achieved by increasing R
The bandwidth then decreases rapidly as shown by the gain
of –16V/V plot in the Typical Characteristic curves.
REVERSE ISOLATION (S
)
12
Reverse isolation is a measure of how much power injected
into the output pin makes it back to the source. This is rarely
specified for an op amp because it is so good. Op amps are
very nearly uni-directional signal devices. Below 300MHz,
the noninverting configuration of Figure 1 gives much better
isolation than the inverting of Figure 2. Both are well below
40dB isolation through 350MHz.
LIMITS TO DYNAMIC RANGE
The next set of considerations for RF amplifier applications
are the defined limits to dynamic range. Typical fixed-gain RF
amplifiers include:
• –1dB compression (a measure of maximum output power)
• Two-tone, 3rd-order, output intermodulation intercept (a
measure of achievable spurious-free dynamic range)
• Noise figure (a measure of degradation in signal to noise
ratio in passing through the amplifier)
–1dB COMPRESSION
The definition for –1dB compression power is that output
power where the actual power is 1dB less than the input
power plus the log gain. In classic RF amplifiers, this is
typically 10dB less than the 3rd-order intercept. That relation-
ship does not hold for op amps since their intercept is
considerably improved by loop gain to be far more than 10dB
higher than the –1dB compression. A simple estimate for
–1dB compression for the OPA695 is the maximum non-slew
limited output voltage swing available at the matched load
converted into a power with 1dB added to satisfy the defini-
tion. For the OPA695 on 5V supplies, its output will deliver
approximately 4.0V at the output pin or 2.0V at the matched
load. The conversion from V
to power (for a sine wave) is:
PP
V
PP
2 2
P dBm
10
log
O
0 001 50
.
Converting this 4.0V
swing at the load to dBm gives
PP
16dBm; adding 1dB to this (to satisfy the definition) gives a
–1dB compression of 17dBm for the OPA695 operating on
5V supplies. This will be a good estimate for frequencies
that require less than the full slew rate of the OPA695.
16
The maximum frequency of operation given an available
slew rate and desired peak output swing (at the output pin for
a sine wave) is:
in Figure 2.
F
Putting in the 4600V/ s slew rate available in the inverting
mode of operation and the 4.0V peak output swing at the
output pin gives a maximum frequency of 259MHz. This is
the maximum frequency where the –1dB compression would
be 17dBm at the matched load. Higher useable bandwidths
are possible at lower output powers, as shown in the Large
Signal Bandwidth curves. As those graphs show, 7V
puts are possible with almost perfect frequency response
flatness through 100MHz for both non-inverting or inverting
operation.
TWO-TONE 3rd-ORDER OUTPUT
INTERMODULATION INTERCEPT (OP
In narrowband IF strips, each amplifier typically feeds into a
bandpass filter that attenuates most harmonic distortion
terms. The most troublesome remaining distortion is the 3rd-
order, two-tone intermodulations that can fall very close (in
frequency) to the desired signals and cannot be filtered out.
If two test frequencies are defined at F
the 3rd-order intermodulation distortion products will fall at
F
+ 3 F and F
O
equal, the OPA695 will produce 3rd-order spurious terms
(P
) that are at these frequencies and at a power level below
S
the test power levels given by:
The 3rd-order intercept plot shown in the Typical Character-
istic curves shows a very high intercept at low frequencies
that decreases with increasing frequency. This intercept is
defined at the matched load to allow direct comparison with
fixed-gain RF amplifiers. To produce a 2V
envelope at the matched load, each power level must be
4dBm at the matched load (1V
performance curve for inverting operation, at 50MHz (41.5dBm
intercept) the 3rd-order spurious will be 2 • (41.5 – 4) = 75dB
below these 4dBm test tones. This is an exceptionally low
distortion for an amplifier that only uses 13mA supply current.
Considerable improvement from this level of performance is
(3)
also possible if the output drives directly into the lighter load
2
of an ADC input (see High SFDR Differential ADC driver
section).
This very high intercept versus quiescent power is achieved
by the high loop gain of the OPA695. This loop gain does,
however, decrease with frequency, giving the decreasing
OP3 performance shown in the Typical Characteristics. Ap-
plication as an IF amplifier through 200MHz is possible with
output intercepts exceeding 21dBm at 200MHz. Intercept
performance will vary slightly with gain setting decreasing at
higher gains (that is, gains greater than the 8V/V, or 12dB,
gain used in the Typical Characteristic curves) and increas-
ing at lower gains.
www.ti.com
Slew Rate
F
MAX
2
V
( .
0 707
)
p
PP
)
3
+ F and F
O
O
– 3 F. If the two test power levels (P
O
P
–
P
2
OP
–
P
T
S
3
T
total two-tone
PP
). Using Equation 5, and the
PP
OPA695
SBOS293G
(4)
out-
– F,
) are
T
(5)

Related parts for OPA695IDBVRG4

Part Number DescriptionManufacturer Datasheet
  OPA695ID IC OPAMP CFB 1.7GHZ SGL 8SOIC Texas Instruments
OPA695IDBVR  OPA695IDBVR IC OPAMP CFB 1.7GHZ SGL SOT23-6 Texas Instruments
  OPA695IDRG4 IC OPAMP CFB 1.7GHZ SGL 8SOIC Texas Instruments
OPA695IDBVT  OPA695IDBVT IC OPAMP CFB 1.7GHZ SGL SOT23-6 Texas Instruments
OPA695IDGKT  OPA695IDGKT IC OPAMP CURR-FDBK 8-MSOP Texas Instruments
  OPA695IDGKR IC OPAMP CURR-FDBK 8-MSOP Texas Instruments
  OPA695IDR IC OPAMP CFB 1.7GHZ SGL 8SOIC Texas Instruments
OPA695IDBVTG4  OPA695IDBVTG4 IC OPAMP CFB 1.7GHZ SGL SOT23-6 Texas Instruments
  OPA695IDG4 IC OPAMP CFB 1.7GHZ SGL 8SOIC Texas Instruments
OPA694  OPA694 The OPA694 is an ultra-wideband, low-power, current feedback operational amplifier featuring high slew rate and low differential gain/phase errors Texas Instruments
OPA695  OPA695 The OPA695 is a very high bandwidth, current-feedback op amp that combines exceptional 4300V/µs slew rate and low input voltage noise to deliver a precision low cost, high dynamic range Intermediate Frequency (IF) amplifier Texas Instruments
OPA690  OPA690 The OPA690 represents a major step forward in unity-gain stable, voltage-feedback op amps Texas Instruments
  OPA698M The OPA698 is a wideband, unity gain stable voltage-feedback op amp that offers bipolar output voltage limiting Texas Instruments
  OPA699M The OPA699 is a wideband, voltage feedback op amp that offers bipolar output voltage limiting, and is stable for gains Texas Instruments
OPA692ID  OPA692ID IC AMP VIDEO BUFF WDBND 8-SOIC Texas Instruments