LP2951CMM/NOPB National Semiconductor, LP2951CMM/NOPB Datasheet - Page 15

• Manufacturer Part Number: LP2951CMM/NOPB
• Description: IC VREG ADJ MICRPWR 8-MSOP
• Manufacturer: National Semiconductor

Specifications of LP2951CMM/NOPB

• Regulator Topology: Positive Adjustable
• Voltage - Output: 1.24 ~ 29 V
• Voltage - Input: Up to 30V
• Voltage - Dropout (typical): 0.38V @ 100mA
• Number Of Regulators: 1
• Current - Output: 100mA
• Operating Temperature: -40°C ~ 125°C
• Mounting Type: Surface Mount
• Package / Case: 8-MSOP, Micro8™, 8-uMAX, 8-uSOP,
• Voltage Regulator Type: Linear
• Topology: LDO
• Regulator Output Type: Adjustable
• Polarity Type: Positive
• Number Of Outputs: Single
• Input Voltage (max): 30V
• Output Voltage: 1.24 to 29V
• Package Type: MSOP
• Output Current: 100mA
• Load Regulation: 0.1%
• Line Regulation: 0.1%
• Output Voltage Accuracy: ±0.5%
• Operating Temp Range: -40C to 125C
• Operating Temperature Classification: Automotive
• Pin Count: 8
• Mounting: Surface Mount
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Current - Limit (min): -
• Lead Free Status / Rohs Status: Compliant
• Other names: LP2951CMM; LP2951CMMTR

*See Application Hints
**Drive with TTL-high to shut down. Ground or leave open if shutdown fea-
ture is not to be used.
Note: Pins 2 and 6 are left open.
REDUCING OUTPUT NOISE
In reference applications it may be advantageous to reduce
the AC noise present at the output. One method is to reduce
the regulator bandwidth by increasing the size of the output
capacitor. This is the only way noise can be reduced on the
3 lead LP2950 but is relatively inefficient, as increasing the
capacitor from 1μF to 220μF only decreases the noise from
430μV to 160μV rms for a 100kHz bandwidth at 5V output.
Noise can be reduced fourfold by a bypass capacitor across
R
Pick
or about 0.01μF. When doing this, the output capacitor must
be increased to 3.3μF to maintain stability. These changes
reduce the output noise from 430μV to 100μV rms for a
1
, since it reduces the high frequency gain from 4 to unity.
FIGURE 2. Adjustable Regulator
854607
15
100kHz bandwidth at 5V output. With the bypass capacitor
added, noise no longer scales with output voltage so that im-
provements are more dramatic at higher output voltages.
LLP MOUNTING
The SDC08A (No Pullback) 8-Lead LLP package requires
specific mounting techniques which are detailed in National
Semiconductor Application Note # 1187. Referring to the sec-
tion PCB Design Recommendations in AN-1187 (Page 5),
it should be noted that the pad style which should be used
with the LLP package is the NSMD (non-solder mask defined)
type. Additionally, it is recommended the PCB terminal pads
to be 0.2 mm longer than the package pads to create a solder
fillet to improve reliability and inspection.
The thermal dissipation of the LLP package is directly related
to the printed circuit board construction and the amount of
additional copper area connected to the DAP.
The DAP (exposed pad) on the bottom of the LLP package is
connected to the die substrate with a conductive die attach
adhesive. The DAP has no direct electrical (wire) connection
to any of the eight pins. There is a parasitic PN junction be-
tween the die substrate and the device ground. As such, it is
strongly recommend that the DAP be connected directly to
the ground at device lead 4 (i.e. GND). Alternately, but not
recommended, the DAP may be left floating (i.e. no electrical
connection). The DAP must not be connected to any potential
other than ground.
For the LP2951 in the SDC08A 8-Lead LLP package, the
junction-to-case thermal rating, θ
case is the bottom of the package at the center of the DAP.
The junction-to-ambient thermal performance for the LP2951
in the SDC08A 8-Lead LLP package, using the JEDEC
JESD51 standards is summarized in the following table:
JESD 51-3
JESD 51-7
2-Layer
4-Layer
JEDEC
JEDEC
Board
Type
Thermal
None
Vias
1
2
4
6
JC
14.2°C/W
14.2°C/W
14.2°C/W
14.2°C/W
14.2°C/W
, is 14.2°C/W, where the
θ
JC
www.national.com
185°C/W
68°C/W
60°C/W
51°C/W
48°C/W
θ
JA