ADP3335ARMZ-3.3RL7 Analog Devices Inc, ADP3335ARMZ-3.3RL7 Datasheet - Page 9

• Manufacturer Part Number: ADP3335ARMZ-3.3RL7
• Description: IC REG LDO 3.3V 500MA 8-MSOP
• Manufacturer: Analog Devices Inc
• Series: anyCAP®r

Specifications of ADP3335ARMZ-3.3RL7

• Package / Case: 8-MSOP, Micro8™, 8-uMAX, 8-uSOP,
• Mounting Type: Surface Mount
• Current - Output: 500mA
• Voltage - Output: 3.3V
• Voltage - Input: Up to 12V
• Operating Temperature: -40°C ~ 85°C
• Regulator Topology: Positive Fixed
• Voltage - Dropout (typical): 0.2V @ 500mA
• Number Of Regulators: 1
• Primary Input Voltage: 12V
• Output Voltage Fixed: 3.3V
• Dropout Voltage Vdo: 200mV
• No. Of Pins: 8
• Output Current: 500mA
• Operating Temperature Range: -40°C To +85°C
• Msl: MSL 3 - 168 Hours
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Current - Limit (min): -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

THEORY OF OPERATION
The ADP3335 uses a single control loop for regulation and
reference functions. The output voltage is sensed by a resistive
voltage divider, R1 and R2, which is varied to provide the
available output voltage option. Feedback is taken from this
network by way of a series diode, D1, and a second resistor
divider, R3 and R4, to the input of an amplifier.
A very high gain error amplifier is used to control this loop. The
amplifier is constructed in such a way that equilibrium
produces a large, temperature proportional input offset voltage
that is repeatable and very well controlled. The temperature
proportional offset voltage combines with the complementary
diode voltage to form a virtual band gap voltage implicit in the
network, although it never appears explicitly in the circuit.
This patented design makes it possible to control the loop with
only one amplifier. This technique also improves the noise
characteristics of the amplifier by providing more flexibility in
the trade-off of noise sources that leads to a low noise design.
The R1 and R2 divider is chosen in the same ratio as the band
gap voltage to the output voltage. Although the R1 and R2
resistor divider is loaded by the D1 diode and a second
divider—R3 and R4, the values can be chosen to produce a
NONINVERTING
INPUT
WIDEBAND
DRIVER
Q1
ADP3335
Figure 23. Functional Block Diagram
COMPENSATION
CAPACITOR
g
m
PTAT
V
OS
R4
GND
(V
ATTENUATION
BANDGAP
CURRENT
PTAT
R3 D1
/V
OUTPUT
OUT
)
R2
R1
(a)
R
C
LOAD
LOAD
Rev. B | Page 9 of 16
temperature stable output. This unique arrangement specifically
corrects for the loading of the divider, thus avoiding the error
resulting from base current loading in conventional circuits.
The patented amplifier controls a new and unique noninverting
driver that drives the pass transistor, Q1. This special nonin-
verting driver enables the frequency compensation to include
the load capacitor in a pole-splitting arrangement to achieve
reduced sensitivity to the value, type, and ESR of the load
capacitance.
Most LDOs place very strict requirements on the range of ESR
values for the output capacitor, because they are difficult to
stabilize due to the uncertainty of load capacitance and
resistance. The ESR value required to keep conventional LDOs
stable, moreover, changes depending on load and temperature.
These ESR limitations make designing with LDOs more
difficult because of their unclear specifications and extreme
variations over temperature.
With the ADP3335, ESR limitations are no longer a source of
design constraints. The ADP3335 can be used with virtually any
good quality capacitor and with no constraint on the minimum
ESR. This innovative design allows the circuit to be stable with
just a small 1 μF capacitor on the output. Additional advantages
of the pole-splitting scheme include superior line noise reject-
tion and very high regulator gain, which lead to excellent line
and load regulation. Impressive ±1.8% accuracy is guaranteed
over line, load, and temperature.
Additional features of the circuit include current limit, thermal
shutdown, and noise reduction.
ADP3335