LX8584-00CP Microsemi Analog Mixed Signal Group, LX8584-00CP Datasheet
LX8584-00CP
Specifications of LX8584-00CP
Related parts for LX8584-00CP
LX8584-00CP Summary of contents
Page 1
... J 1. 125 1.2V Note: xx refers to output voltage, please see table to right. Available in Tape & Reel. Append the letters “TR” to the part number. (i.e. LX8584-xxCP-TR) Copyright © 1997 Rev. 1.3, 2005-11-11 11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570 ® ...
Page 2
... Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570 ® 7A Low Dropout Positive Regualtors . , θ T 2.7°C θ A 60°C/W MBIENT JA x θ Microsemi Integrated Products Division LX8584x- RODUCTION ATA HEET TAB is GND ADJ/GND ACKAGE (Top View) RoHS 100% Matte Tin Lead Finish IN OUT ...
Page 3
... Dropout Voltage LX8584/84B LX8584/84B Minimum Load Current Maximum Output Current Temperature Stability Long Term Stability RMS Output Noise (% OUT LX8584-33 / 84A-33 / 84B-33 (3.3V Fixed LX8584B-33 Output Voltage LX8584/84A-33 Line Regulation (Note 2) Load Regulation (Note 2) Thermal Regulation Ripple Rejection (Note 3) Quiescent Current ...
Page 4
... Use of an output capacitor is REQUIRED with the LX8584 / 84A / 84B series. Please see the table below for recommended minimum capacitor values. These regulators offer a more tightly controlled reference voltage tolerance and superior reference stability when measured against the older pin-compatible regulator types that they replace ...
Page 5
... Output ripple will be twice as bad as it would be if the ADJ pin were to be bypassed to ground with a properly selected capacitor. OUTPUT VOLTAGE The LX8584/84A/84B ICs develop a 1.25V reference voltage between the output and the adjust terminal (See Figure 2). By placing a resistor, R1, between these two terminals, a constant current is caused to flow through R1 and down through R2 to set the overall output voltage ...
Page 6
... DROPOUT(MAX) installed regulator. THERMAL CONSIDERATIONS The LX8584/84A/84B regulators have internal power and thermal limiting circuitry designed to protect each device under overload conditions. For continuous normal load conditions, however, maximum junction temperature ratings must not be exceeded important to give careful consideration to all sources of thermal resistance from junction to ambient ...
Page 7
... Figure 6 – 5V Regulator with Shutdown LX8584/84A/84B-33 OUT IN GND Figure 7 – Fixed 3.3V Output Regulator ) + (V ) DROPOUT(MAX) Microsemi Integrated Products Division LX8584x- RODUCTION ATA HEET LX8584/84A/84B OUT IN V OUT ADJ R1 121Ω C2 C1* 100µF 10µ 1.25V 121Ω 1% 100µF 365Ω ...
Page 8
... S 1. 5.84 U 0.508 Note: 1. Dimensions do not include mold flash or protrusions; J these shall not exceed 0.155mm(.006”) on any side. Lead dimension shall not include solder coverage. Microsemi Integrated Products Division LX8584x- ATA HEET I ILLIMETERS NCHES MAX MIN MAX 15.88 0.560 0.625 10 ...
Page 9
... Pentium is a trademark of Intel Corporation\ PowerPC is a trademark of Motorola Inc. Copyright © 1997 Rev. 1.3, 2005-11-11 11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570 ® 7A Low Dropout Positive Regualtors P RODUCTION Microsemi Integrated Products Division LX8584x- ATA HEET Page 9 ...