MIC29150-3.3BT Micrel Inc, MIC29150-3.3BT Datasheet
MIC29150-3.3BT
Specifications of MIC29150-3.3BT
Available stocks
Related parts for MIC29150-3.3BT
MIC29150-3.3BT Summary of contents
Page 1
... On the MIC29xx1 and MIC29xx2, the ENABLE pin may be tied to VIN not required for ON/OFF control. The MIC29150/29300/29500 are available in 3-pin and 5-pin TO-220 and surface mount TO-263 (D The MIC29750 7.5A regulators are available in 3-pin and 5-pin TO-247 packages ...
Page 2
... Micrel, Inc. Ordering Information Part Number Standard MIC29150-3.3BT MIC29150-3.3WT MIC29150-3.3BU MIC29150-3.3WU MIC29150-5.0BT MIC29150-5.0WT MIC29150-5.0BU MIC29150-5.0WU MIC29150-12BT MIC29150-12WT MIC29150-12BU MIC29150-12WU MIC29151-3.3BT MIC29151-3.3WT MIC29151-3.3BU MIC29151-3.3WU MIC29151-5.0BT MIC29151-5.0WT MIC29151-5.0BU MIC29151-5.0WU MIC29151-12BT MIC29151-12WT MIC29151-12BU MIC29151-12WU MIC29152BT MIC29152WT MIC29152BU MIC29152WU — MIC29152WD (3) MIC29153BT Contact Factory (3) MIC29153BU Contact Factory MIC29300-3 ...
Page 3
... TO-263 3.3 7.5A 3-Pin TO-247 5 7.5A 3-Pin TO-247 3.3 7.5A 5-Pin TO-247 5 7.5A 5-Pin TO-247 Adj. 7.5A 5-Pin TO-247 5-Pin TO-220 Fixed Voltage (T) MIC29151/29301/29501/29751 5-Pin TO-220 Adjustable with Flag (T) MIC29153/29303/29503 5-Pin TO-247 Fixed Voltage (WT) MIC29751 2 3-Pin TO-263 (D Pak) (UT) MIC29150/29300 Package M9999-050510-B ...
Page 4
... OUTPUT: The regulator output voltage 5 ADJUST: Adjustable regulator feedback input that connects to the resistor voltage divider that is placed from OUTPUT to GND in order to set the output voltage. 1 FLAG: Active low error flag output signal that indicates an output fault condition 4 MIC29150/29300/29500/29750 2 Pak) Adjustable Voltage (U) MIC29302/29502 MIC29152 M9999-050510-B ...
Page 5
... OUT IN OUT I = 7.5A OUT × I OUT OUT ( OUT ( OUT ( OUT ( OUT 5 MIC29150/29300/29500/29750 (2) TO-220 (θ ).........................................................2°C/W JC TO-263 (θ ).........................................................2°C/W JC TO-247 (θ ) .....................................................1.5°C/W JC TO-252 (θ ).........................................................3°C/W JC TO-252 (θ ) ......................................................56°C/W JA ≤ +125°C, unless noted. J Min Typ –1 (5) –2 0.06 0 220 350 ...
Page 6
... Parameter Condition e , Output Noise C = 10µ Voltage (10Hz to 100kHz 33µ 100mA L Ground Current in MIC29150/1/2/3 only V Shutdown Reference MIC29xx2/MIC29xx3 Reference Voltage Reference Voltage Adjust Pin Bias Current (10) Reference Voltage Temperature Coefficient Adjust Pin Bias Current Temperature Coefficient Flag Output (Error Comparator) MIC29xx1/29xx3 ...
Page 7
... Specification for packaged product only. 5. Full load current ( defined as 1.5A for the MIC29150, 3A for the MIC29300, 5A for the MIC29500, and 7.5A for the MIC29750 families Dropout voltage is defined as the input-to-output differential when the output voltage drops to 99% of its normal value with V 7 ...
Page 8
... Micrel, Inc. Typical Characteristics MIC2915x May 2010 MIC29150/29300/29500/29750 8 M9999-050510-B ...
Page 9
... Micrel, Inc. May 2010 MIC29150/29300/29500/29750 9 M9999-050510-B ...
Page 10
... Micrel, Inc. Typical Characteristics MIC2930x May 2010 MIC29150/29300/29500/29750 10 M9999-050510-B ...
Page 11
... Micrel, Inc. May 2010 MIC29150/29300/29500/29750 11 M9999-050510-B ...
Page 12
... Micrel, Inc. Typical Characteristics MIC2950x May 2010 MIC29150/29300/29500/29750 12 M9999-050510-B ...
Page 13
... Micrel, Inc. May 2010 MIC29150/29300/29500/29750 13 M9999-050510-B ...
Page 14
... Micrel, Inc. Typical Characteristics MIC2975x May 2010 MIC29150/29300/29500/29750 14 M9999-050510-B ...
Page 15
... Micrel, Inc. May 2010 MIC29150/29300/29500/29750 15 M9999-050510-B ...
Page 16
... Micrel, Inc. Functional Diagram May 2010 MIC29150/29300/29500/29750 16 M9999-050510-B ...
Page 17
... But Micrel’s Super ßeta PNP process reduces this drive requirement to merely 1% of the load current. The MIC29150/29300/29500/29750 family of regulators are fully protected from damage due to fault conditions. Current limiting is provided. This limiting is linear; output current under overload conditions is constant. Thermal ...
Page 18
... Input and GND is recommended. This capacitor should have good characteristics to above 250kHz. Minimum Load Current The MIC29150–29750 regulators are specified between finite loads. If the output current is too small, leakage currents dominate and the output voltage rises. The following minimum load current swamps any expected ...
Page 19
... Micrel, Inc. Package Information May 2010 3-Pin TO-220 (T) 5-Pin TO-220 (T) 19 MIC29150/29300/29500/29750 M9999-050510-B ...
Page 20
... Micrel, Inc. May 2010 5-Pin TO-263 (U) 3-Pin TO-263 (U) 20 MIC29150/29300/29500/29750 M9999-050510-B ...
Page 21
... Micrel, Inc. May 2010 5-Pin TO-247 (WT) 3-Pin TO-247 (WT) 21 MIC29150/29300/29500/29750 M9999-050510-B ...
Page 22
... Purchaser’s use or sale of Micrel Products for use in life support appliances, devices or systems is a Purchaser’s own risk and Purchaser agrees to fully May 2010 5-Pin TO-252 (D) indemnify Micrel for any damages resulting from such use or sale. © 2009 Micrel, Incorporated. 22 MIC29150/29300/29500/29750 M9999-050510-B ...
Page 23
... Edited EC table and diagrams, added pin descriptions. 9/18/09 Added EVB Circuit and BOM. Text added to Thermal Design section 9/22/09 Removed EVB Circuit and BOM 10/12/09 Update drawings and curves May 2010 MIC29150/29300/29500/29750 23 Revisions 15 16 072309_AMSr1 091809_AMS 092409_AMS Martha taken over for Mike ...