RES 2.2K OHM 1/4W 5% 1210 SMD

MCR25JZHJ222

Manufacturer Part NumberMCR25JZHJ222
DescriptionRES 2.2K OHM 1/4W 5% 1210 SMD
ManufacturerRohm Semiconductor
SeriesMCR25
MCR25JZHJ222 datasheet
 


Specifications of MCR25JZHJ222

Resistance (ohms)2.2KPower (watts)0.25W, 1/4W
CompositionThick FilmTemperature Coefficient±200ppm/°C
Tolerance±5%Size / Dimension0.126" L x 0.098" W (3.20mm x 2.50mm)
Height0.022" (0.55mm)Lead StyleSurface Mount (SMD - SMT)
Package / Case1210 (3225 Metric)Resistance In Ohms2.20K
Case1210 (3225 metric)Lead Free Status / RoHS StatusLead free / RoHS Compliant
Features-Other namesRHM2.2KBETR
1
Page 1
2
Page 2
3
Page 3
4
Page 4
Page 1/4

Download datasheet (159Kb)Embed
Next
Thick Film Chip Resistors
MCR25 (1210 size: 1 / 4W)
Features
1) Made of same material as the general purpose chip resistors (MCR10 / 18).
2) Highly reliable chip resistor
Ruthenium oxide resistive material offers superior resistance to the elements.
3) Electrodes not corroded by soldering
Suitable for re-flow soldering.
4) ROHM resistors have approved ISO9001-/ ISO/TS 16949- certification.
Design and specifications are subject to change without notice. Carefully check the specification sheet before using or
ordering it.
Ratings
Item
Power must be derated according to the power derating curve in
Rated power
Figure 1 when ambient temperature exceeds 70°C.
100
80
60
40
20
0
−55
AMBIENT TEMPERATURE (°C)
The voltage rating is calculated by the following equation. If the value
Rated voltage
obtained exceeds the limiting element voltage, the voltage rating is
equal to the maximum operating voltage.
E = P × R
Nominal resistance
See Table 1.
Operating temperature
Jumper type
Table 1
Resistance
Max. 50mΩ
Resistance tolerance
Rated current
2A
−55°C to +155°C
Operating temperature
F (±1%)
J (±5%)
•Before using components in circuits where they will be exposed to transients such as pulse loads (short-duration, high-level loads), be certain to evaluate the
component in the mounted state. In addition, the reliability and performance of this component cannot be guaranteed if it is used with a steady state voltage that
is greater than its rated voltage.
www.rohm.com
2009 ROHM Co., Ltd. All rights reserved.
c
Conditions
0
70
100
125
155
Fig.1
E: Rated voltage (V)
P: Rated power (W)
R: Nominal resistance (Ω)
Resistance range
(Ω)
10 ≤ R ≤ 1M
(E24,96)
1.0 ≤ R ≤ 2.0
(E24)
2.2 ≤ R ≤ 5.1
(E24)
5.6 ≤ R ≤ 3.3M
(E24)
1/3
Specifications
0.25W (1 / 4W)
at 70°C
Limiting element voltage
200V
−55°C to +155°C
Resistance temperature coefficient
(ppm/°C)
±100
500±350
±500
±200
2009.10 - Rev.E

MCR25JZHJ222 Summary of contents

  • Page 1

    ... Thick Film Chip Resistors MCR25 (1210 size 4W) Features 1) Made of same material as the general purpose chip resistors (MCR10 / 18). 2) Highly reliable chip resistor Ruthenium oxide resistive material offers superior resistance to the elements. 3) Electrodes not corroded by soldering Suitable for re-flow soldering. 4) ROHM resistors have approved ISO9001-/ ISO/TS 16949- certification. ...

  • Page 2

    MCR25 Characteristics Item Resistor type J : ±5% Resistance F : ±1% Variation of resistance with temperature ± (2.0%+0.1Ω) Overload A new uniform coating of minimum of 95% of the surface being immersed Solderability and no soldering damage. ± (1.0%+0.05Ω) ...

  • Page 3

    MCR25 Packaging Reel Label (Unit : mm +1.0 φ180 φ60 φ13 ± 0.2 9 −3 −0 0 Part No. Explanation M C Part No. Packaging Specifications Code Resistance tolerance Part No. ...

  • Page 4

    No copying or reproduction of this document, in part or in whole, is permitted without the consent of ROHM Co.,Ltd. The content specified herein is subject to change for improvement without notice. The content specified herein is for the purpose ...