ALM-1412-TR1G Avago Technologies US Inc., ALM-1412-TR1G Datasheet
ALM-1412-TR1G
Specifications of ALM-1412-TR1G
Available stocks
Related parts for ALM-1412-TR1G
ALM-1412-TR1G Summary of contents
Page 1
... Avago Technologies’ leading- edge FBAR filter for exceptional rejection at Cell/PCS- Band frequencies. The ALM-1412 is useable down operation. It achieves low noise figure, high gain and linearity even making it suitable for use in critical low-power GPS applications or during low-battery situations. ...
Page 2
Absolute Maximum Rating T = 25°C A Symbol Parameter Vdd Device Drain to Source Voltage [2] Idd Drain Current Input Power in,max (Vdd = 2.85 V, Idd = 9.0 mA) [4] P Total Power Dissipation diss ...
Page 3
Electrical Specifications T = 25°C, Vdd = +2.85V, Vsd = +2.6V, Idd = 8mA (typ kΩ, Freq = 1.575GHz - Typical Performance A otherwise specified. Table 1. Performance Table at Nominal Operating Conditions Symbol Parameter and Test ...
Page 4
Vdd = +2 V, Vdd = +1.5 V, Vdd = +1 V, Freq = 1.575 GHz – Typical Performance Table 3. Typical Performance at Low Operating Voltages with R2 (See Figures 6 and 7) Set to 0 ohms Symbol Parameter ...
Page 5
RF input Pins pointing out of the page Circuit Symbol Figure 6. Demoboard and application circuit components table Pin Configuration of 4-pin Connector Pins ...
Page 6
... For low-voltage operation such as Vdd = 1 1 may be omitted and SD (Vsd) connected directly to Vdd. x The grounding regime for the ALM-1412 is critical to achieving the PCS- and Cell-Band Rejections shown in Figure 9. Please refer to the PCB Land Patterns section of this document for the exact locations of the grounding vias. ...
Page 7
... ALM-1412 Typical Performance Curves, Vdd = +2.85 V, Vsd = +2.6V, Idd = 8mA (typ) (at 25°C unless specified otherwise) IRL Gain freq= 1.575GHz freq= 1.575GHz dB(S(1,1))=-8.424 dB(S(2,1))=13.513 -10 -20 -30 -40 CELL -50 -60 -70 0.8 0.9 1.0 CELL ind Delta= dep Delta= delta mode ON Figure 8 ...
Page 8
... ALM-1412 Typical Performance Curves kΩ (at 25°C unless specified otherwise 5mA 10 8mA 8 11mA 6 2.4 2.5 2.6 2.7 2.8 2.9 Vdd (V) Figure 10. Gain vs. Vdd vs. Idd 5mA 8mA 2 11mA 0 2.4 2.5 2.6 2.7 2.8 2.9 Vdd (V) Figure 12. IIP3 vs. Vdd vs. Idd 1.6 1.8 2 ...
Page 9
... ALM-1412 Typical Performance Curves kΩ (at 25°C unless specified otherwise Vdd (V) Figure 15. Cell band rejection vs. Vdd vs. Idd 5mA 7 5 8mA 7 0 11mA Figure 16. PCS band rejection vs. Vdd vs. Idd 5mA 8mA 11mA Vdd (V) ...
Page 10
... ALM-1412 Typical Performance Curves kΩ (at 25°C unless specified otherwise 2.4 2.5 2.6 2.7 2.8 2.9 Vdd (V) Figure 17. Gain vs. Vdd vs. Temp (Idd = 8 mA 2.4 2.5 2.6 2.7 2.8 2.9 Vdd (V) Figure 19. IIP3 vs. Vdd vs. Temp (Idd = Vdd (V) Figure 21. Cell band rejection vs. Vdd vs. Temp (Idd = 8 mA ...
Page 11
... ALM-1412 Scattering Parameter and Noise Parameter Measurement REFERENCE PLANE 1 Figure 23. Scattering and noise parameter reference planes INPUT FILTER MATCH REFERENCE PLANE 8 MODULE OUTLINE ...
Page 12
... ALM-1412 Typical Scattering Parameters at 25°C, Vdd = 2.85 V, Vsd = +2.6V, Idd = 8mA (typ) The S- and Noise Parameters are measured using the PCB described in Figures 6 and 7. The PCB material is 10 mils Rogers® RO4350. Figure 23 shows the input and output reference planes. The circuit values, with the exception of L3, are as indicated in Figure 6 ...
Page 13
... ALM-1412 Typical Scattering Parameters at 25°C, Vdd = 2.85 V, Vsd = +1.8V, Idd = 4.5mA (typ) Freq. S11 S11 (GHz) Mag. Ang 0.3 0.9364 50.71 0.5 0.9751 15.23 0.7 0.9673 -6.10 0.8 0.9594 -17.41 0.8275 0.9620 -18.73 0.9 0.9561 -25.18 1.0 0.9702 -33.12 1.1 ...
Page 14
... This allows the use of relatively inexpensive chip inductors for external matching. x The NF performance of the ALM-1412 is also very resilient to operating conditions. For example, at Idd = 4.5 mA, the degradation only 0.1 dB, and not more than 0.15 dB degradation over temperature. ...
Page 15
Package Dimensions PIN 1 ORIENTATION 1412 WWYY 3.30 r 0.10 TOP VIEW NOTES: 1. ALL DIMENSIONS ARE IN MILLIMETERS. 2. DIMENSIONS ARE INCLUSIVE OF PLATING. 3. DIMENSIONS ARE EXCLUSIVE OF MOLD FLASH AND METAL BURR. PCB Land Patterns and Stencil ...
Page 16
Device Orientation REEL USER FEED DIRECTION COVER TAPE Tape Dimensions MAX SECTION REF. 0. SECTION REF. R 0.65 16 1412 CARRIER WWYY TAPE P10 (3) P2 ...
Page 17
Reel Dimensions - 13 inch DATE CODE EMBOSSED LETTERING 7.5mm HEIGHT EMBOSSED LINE (2x) 89.0mm LENGTH LINES 147.0mm AWAY FROM CENTER POINT ESD LOGO 6 PS RECYCLE LOGO ...