AMMP-6222-BLKG Avago Technologies US Inc., AMMP-6222-BLKG Datasheet - Page 9

• Manufacturer Part Number: AMMP-6222-BLKG
• Description: IC MMIC AMP LNA 7GHZ-21GHZ 8SMD
• Manufacturer: Avago Technologies US Inc.
• Series: -r

Specifications of AMMP-6222-BLKG

• Rf Type: WiMax
• Gain: 24dB
• Current - Supply: 120mA
• Frequency: 7GHz ~ 21GHz
• Noise Figure: 2.3dB
• P1db: 15.5dBm
• Package / Case: 8-SMD
• Voltage - Supply: 3 V ~ 5 V
• Frequency Rf: 21GHz
• Noise Figure Typ: 2.3dB
• Supply Current: 120mA
• Msl: MSL 2A - 4 Weeks
• Supply Voltage Range: 3V To 5V
• Frequency Max: 21GHz
• Test Frequency: -
• Number Of Channels: 1
• Power Supply Requirement: Single
• Single Supply Voltage (min): 3V
• Single Supply Voltage (typ): 4V
• Single Supply Voltage (max): 5V
• Package Type: SMD
• Dual Supply Voltage (min): Not RequiredV
• Dual Supply Voltage (typ): Not RequiredV
• Dual Supply Voltage (max): Not RequiredV
• Pin Count: 8
• Mounting: Surface Mount
• Filter Terminals: SMD
• Frequency Min: 7GHz
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Test Frequency: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

AMMP-6222 Application and Usage
Figure 19. Low Current, Low Output Power State
Figure 20. High Current, High Output Power State
Figure 21. Evaluation/Test Board (available to qualified customer request)
Figure 22. Simplified High Linearity LNA Schematic
9
In
IN
IN
8
8
1
1
7
7
Vdd
Vdd
4V
4V
2
6
2
6
100pF
0.1uF
0.1uF
Open
100pF
3
5
3
5
Vd1
Matching
Network
4
4
OUT
OUT
Matching
Network
Vd2
Biasing and Operation
The AMMP-6222 is normally biased with a positive drain
supply connected to the VDD pin through bypass capacitor
as shown in Figures 19 and 20. The recommended
drain supply voltage for general usage is 4V and the
corresponding drain current is approximately 120mA. It is
important to have 0.1uF bypass capacitor and the capacitor
should be placed as close to the component as possible.
Aspects of the amplifier performance may be improved
over a narrower bandwidth by application of additional
conjugate, linearity, or low noise (7opt) matching.
For receiver front end low noise applications where high
power and linearity are not often required, the AMMP-
6222 can be set in low current state when pin # 5 is open as
shown in Figure 19. In this configuration, the bias current
is approximately 90mA, 95mA and 100mA for 3V, 4V and
5V respectively.
In applications where high output power and linearity
are often required such as LO or transmitter drivers, the
AMMP-6222 can be selected to operate at its highest
output power by grounding pin # 5 as shown in Figure 20.
At 5V, the amplifier can provide Psat of ~ 20dBm. The bias
current in this configuration is 115mA, 120mA and 125mA
for 3V, 4V and 5V respectively.
Refer the Absolute Maximum Ratings table for allowed DC
and thermal conditions.
SELECT
Out