UPC2709TB-EVAL NEC, UPC2709TB-EVAL Datasheet
UPC2709TB-EVAL
Specifications of UPC2709TB-EVAL
Related parts for UPC2709TB-EVAL
UPC2709TB-EVAL Summary of contents
Page 1
... PC2709TB-E3-A 6-pin super minimold Remark To order evaluation samples, please contact your local NEC sales office (Part number for sample order: PC2709TB-A). The information in this document is subject to change without notice. Before using this document, please confirm that this is the latest version. ...
Page 2
... PIN CONNECTIONS (Top View PRODUCT LINE- V-BIAS SILICON MMIC MEDIUM OUTPUT POWER AMPLIFIER (T = +25° 5 out (sat) Part No. (GHz) (dBm) PC2708T 2.9 +10.0 PC2708TB PC2709T 2.3 +11.5 PC2709TB PC2710T 1.0 +13.5 PC2710TB PC2776T 2.7 +8.5 PC2776TB Remark Typical performance. Please refer to ELECTRICAL CHARACTERISTICS in detail. ...
Page 3
SYSTEM APPLICATION EXAMPLE EXAMPLE OF DBS CONVERTERS BS Antenna (DBS ODU) Parabola Antenna EXAMPLE OF 900 MHz BAND, 1.5 GHz BAND DIGITAL CELLULAR TELEPHONE RX SW Driver TX PA PC2709TB ...
Page 4
... Ground pin. This pin should be connected to system ground with minimum inductance. Ground pattern on the board should be formed as wide as possible. All the ground pins must be con- nected together with wide ground pattern to decrease impedance defference. Data Sheet P12653EJ3V0DS00 PC2709TB Internal Equivalent Circuit ...
Page 5
ABSOLUTE MAXIMUM RATINGS Total Circuit Current ...
Page 6
... V fluctuation. CC The coupling capacitors, connected to the input and output pins, are used to cut the DC and minimize RF serial impedance. Their capacitance are therefore selected as lower impedance against a 50 perform as high pass filters, suppressing low frequencies to DC. To obtain a flat gain from 100 MHz upwards, 1 000 pF capacitors are used in the test circuit. In the case of under 10 MHz operation, increase the value of coupling capacitor such as 10 000 pF ...
Page 7
ILLUSTRATION OF THE TEST CIRCUIT ASSEMBLED ON EVALUATION BOARD Top View Mounting direction COMPONENT LIST Value C 1 000 pF L 300 nH For more information on the use of this IC, refer to the following application note: USAGE AND ...
Page 8
TYPICAL CHARACTERISTICS (Unless otherwise specified, T CIRCUIT CURRENT vs. SUPPLY VOLTAGE 40 No input signal Supply Voltage V (V) CC NOISE FIGURE, POWER GAIN vs. FREQUENCY 8 30 ...
Page 9
OUTPUT POWER vs. INPUT POWER + 1.0 GHz 5 –5 –10 –15 –20 –35 –30 –25 –20 –15 –10 – +10 Input Power P (dBm) ...
Page 10
S-PARAMETERS ( -FREQUENCY 11 S -FREQUENCY 5.0 V) out 0.1 G 1.0 G 3.0 G 3.0 G 0.1 G 2.0 G 1.0 G Data Sheet P12653EJ3V0DS00 PC2709TB ...
Page 11
TYPICAL S-PARAMETER VALUES ( 5 out CC Frequency S 11 MHz MAG. ANG. MAG. 100.0000 0.227 0.2 13.698 200.0000 0.239 1.0 13.724 300.0000 0.245 2.9 13.830 400.0000 0.244 2.5 13.998 ...
Page 12
PACKAGE DIMENSIONS 6-PIN SUPER MINIMOLD (UNIT: mm) 12 2.1 0.1 1.25 0.1 0.1 MIN. Data Sheet P12653EJ3V0DS00 PC2709TB ...
Page 13
... Observe precautions for handling because of electro-static sensitive devices. (2) Form a ground pattern as widely as possible to minimize ground impedance (to prevent undesired oscillation). All the ground pins must be connected together with wide ground pattern to decrease impedance difference. (3) The bypass capacitor should be attached to the V (4) The inductor (L) must be attached between V accordance with desired frequency ...
Page 14
Subject: Compliance with EU Directives CEL certifies, to its knowledge, that semiconductor and laser products detailed below are compliant with the requirements of European Union (EU) Directive 2002/95/EC Restriction on Use of Hazardous Substances in electrical and electronic equipment (RoHS) ...